Witter HN47A Notice De Montage

Fitting
Instructions
MATERIALS
A 1 Tubular Mainframe
B 1 Centre Plate with European facing to 94/20/EC A50-1
C 1 Centre Plate with European facing to 94/20/EC A50-1
D 1 Inner Side Arm (left hand)
E 1 Inner Side Arm (right hand)
F 2 Outer Side Arms
G 2 Bushes (25mm O.D. x 16mm long)
H 10 M10 x 30mm x 1.5 Bolts, Nuts, Lock Washers and Large Flat Washers (40mm O.D)
J 2 M10 x 30mm x 1.5 Bolts, Nuts and Lock Washers
K 4 M8 x 35mm x 1.25 Bolts, Lock Washers and Flat Washers (25mmO.D.)
K 4 M8 Spigot Nuts, M10 Lock Washers and Flat Washers (M10 x 20mm O.D.)
L 4 M10 x 30mm x 1.5 Bolts, Nuts and Lock Washers
M 1 Electrical Plate
N 2 M10 x 45mm x 1.5 Bolts, Nuts, Lock Washers and Large Flat Washers (50mm O.D)
S 2 M12 x 65mm x 1.75 Bolts, Nyloc Nuts
T 1 Safety Chain Plate
CB 2 M16 x 50mm x 2.00 Coupling Bolts, Nuts, Lock Washers
FITTING
1. Remove the bumper (2 upper rear bolts behind plastic caps, 2 tip bolts, 2 wheel arch screws and 2 plastic plugs
on lower edge). Remove the steel bumper beam. Cut bumper as shown. Note: Clear all mastic compound
from the washer and Side Arm seating areas as required.
Note: On vehicles with captive studs at (K) Side Arms (D and E) have to be in place before attaching
Mainframe (A).
2. Remove the plastic plugs at (N). Insert Bushes (G) and loosely attach Mainframe (A) to vehicle using Bolts (N).
3. Loosely attach Side Arms (D, E and F) to Mainframe (A) using Bolts (K, L and J) or Spigot Nuts at (K) as
required.
4. Mark up through Side Arms (D, E and F) for holes (H), drill down from inside the boot and attach using Bolts (H).
Tighten all Bolts and refit the bumper.
5. Attach Centre Plates (B and C), Electrical Plate (M) and Safety Chain Plate (T) to Mainframe (A) using Bolts (S).
6. In order to prevent moisture ingress, once tightened, apply a water-sealing agent to every bolt protruding through the rear
panel.
This towbar must be used with either a Witter Towball (part number Z1) or Class A50-1 or A50-X towball dimensionally
conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar, also for use with Witter Removable
Towball Unit (part number ZR2M000). Towing eye must be removed to fit Removable Towball (See diagram).
Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm , M14 - 150 Nm, M16 - 214 Nm
Remove Towing Eye
to fit ZR2M000
W0001HN47A-FIT$010802220000`Ä
W0001HN47A-FIT$010802220000
For HONDA CIVIC HATCHBACK
HN47A
TOWBAR
(2001-)