Witter HN67AU Instructions De Montage

MATERIALS
A 1 Main Assembly
C 1 Left Sidearm
D 1 Lower Right Sidearm
E 1 Upper Right Sidearm
F 1 Cleat
G 1 Bush (Dia 17 O.D, 56 Lg)
H 1 Bush (Dia 17 O.D, 60 Lg)
J 2 M10 x 35 x 1,5 Bolts, Lock Washers and Flat Washer (40 O.D)
K 4 M10 x 40 x 1.5 Bolts, Nuts, Lock Washers and 8 off Flat Washers (25 O.D)
L 1 M8 x 30 x 1.0, Lock Washer and Flat Washer (20 O.D)
M 1 M10 x 100 x 1.5 Bolt, Nut, Lock Washer and 2 off Flat Washer (25 O.D)
N 1 M10 x 90 x 1.5 Bolt, Nut, Lock Washer and Flat Washer (1 off 25 O.D & 1 off 40 O.D)
P 3 M8 x 30 x 1.0, Lock Washer and Flat Washer (20 O.D)
R 2 M12 x 100 x 1.75 Bolts and Nyloc Nuts (Grade 10.9)
S 1 M6 x 20 x 1.0 Bolt Nyloc Nut and Neopreme Washers.
ZS 2 Neck Spacers
ZE 1 Electrical Plate
CB 2 M16 x 50 x2.0 Bolts, Nuts and Lock Washers.
HN67 Flange neck option – ZF3006. Note: This towbar must be used with either a Witter Towball (part number Z11) or Class
A50-1 or A50-X towball dimensionally Conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
HN67Q Detachable neck option – ZQ3006. Please refer to ZQ fitting instructions for installation.
HN67QF Flange Detachable neck option – ZQF3006. Please refer to ZQ fitting instructions for installation.
Recommended torque settings: Grade 8.8 bolts: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214
Nm Grade 10.9: M12 – 139Nm, M10 – 78Nm
FITTING
1. Remove Bumper, 4 x Torx Screws in boot opening, 3 x plastic push clips on lower edge, 2 x self tapping screw on
bottom edge (1 per side) and 1 x self tapping screw in each wheel arch. Push small tab in wheel arch on top edge of
bumper and pull sideways. Remove rear shelf, boot floor mat, storage box, rear panel lining and right side trim.
2. Remove Left bumper support extension, re-fit inner M8 fixing. Open end of chassis by chain drilling around pre marked
dimples and cutting between holes. Touch up bare metal with appropriate paint or under seal.
3. Locate existing rear most hole through right bumper support extension and drill out to sufficient size to insert bush (G).
4. Insert sidearm (C) into left chassis rail and attach using fixings (J).
5. Insert bush (G) into right bumper support arm and loosely attach (D) & (E) using fixing (M), insert bush (H) through
existing hole in chassis on inside of boot and secure using fixing (N).
6. Drill through spot weld securing rear panel to bumper support arm (see attached picture) and secure using fixing (P).
7. Attach crossbar (A) and cleat (F) to sidearms using fixings (K) and (L).
8. Using bracket (E) as a guide, drill through rear panel taking care not to damage any wiring on inside of boot and attach
bracket (E) using fixings (P). Fully tighten all fixings.
9. Attach the required neck option with appropriate fixings and packers with electrical plate in position shown. Re-fit all trim
and bumper.
Fitting
Instructions
µW0001HN67AU-FIT$020810160000XÄ
W0001HN67AU-FIT$020810160000
For use with either
TOWBAR
For Honda Jazz 2009-
HN67AU
for
HN67A
HN67AQ
HN67AQF