Witter HN69AU Notice De Montage

MATERIALS
A 1 Main Crossbar.
B 1 L/H Sidearm.
C 1 R/H Sidearm.
D 2 Bushes 17O/D 49mm Long.
D1 2 M8 x 75 x 1.25 bolts, Lock washers and Flat Washers 20O/D.
E 2 Towing eye Spacers.
F 6 M10 x 35 x 1.25 fine pitch Bolts, Lock washers and Flat washers 30O/D.
G 2 Bent Flats.
H 4 M8 x 30 x 1.25 bolts, Lock washers and Flat Washers 20O/D.
J 4 M8 x 35 x 1.25 bolts, Lock washers and 8 off Flat Washers 20O/D and Nuts.
K 4 M10 x 35 x 1.25 fine pitch bolts, Lock washers and Flat Washers 20O/D (Form A) and Nuts
M 1 M16 x 100 x 2.00 bolt, Lock washer and Nut.
N 2 M8 x 30 x 1.25 bolts, Lock washers and Flat washers. 20O/D.
FITTING
1. Remove lower part of bumper by removing 2 off tip screws in each wheel arch 2 off bolts at the top when opening the
rear door, remove 3 off plastic clips along bottom edge of bumper 1 off forward clip and 3 off bolts to remove the under
tray,
2. After removal of the under tray remove 4 off plastic clips each side ( three off by wheel arch and one each side toward
middle of the bumper) inside bumper holding the lower bumper to the upper. Disconnect the reversing sensors if fitted
and all wires, unclip and relocate the module (Keyless entry) at the top of the rear panel, the main crossbar should sit
tight up against the bracket at this point.
3. Remove the bumper beam 2 off bolts each side Note: It may be necessary to loosen the beam from its seal with a
sharp blow with a rubber mallet.
4. Remove 2 off bolts one each side at rear of chassis rail behind the rear panel (left hand and right hand sides of vehicle),
release exhaust rubber on R/H side from exhaust manifold, loosely fit part "C" using fixings F bush "D" and fixings D1
(Exhaust rubber should fit through oval cut out ) Loosely Fit sidearm "B" using fixings F and bush "D" with fixings D1.
Loosely attach part "A" with fixings "H" on both sides of vehicle and mark for drilling of holes for fixings "J". remove
5.
part "A" and Drill through marked panel to attach part "G" then re-fit main crossbar "A" with fixings "H" and using
fixings "N" attach to holes at ends of chassis rails finally connecting part "A" to Part "G".
Attach side arms "B" & "C" to main crossbar "A" at inboard positions using fixings "K" and attach centre profiles to
6.
towing eye using spacers "E" and fixing "M".
7. Fully tighten all fixings and re-attach the exhaust mounting rubber.
8. Cut the bumper under tray to suit chosen neck / electrical plate option as per drawing. On models 2015 on it
may be necessary to cut the bumper edge (80mm wide and 20mm deep) at the bumper centre shown below
"BC".
9. Re-fit bumper re-connect wiring, relocate keyless entry sensor.
10. Attach and fully tighten chosen neck option. Check all fixings are tight.
Recommended torque settings: Grade 8.8 bolts: M8 - 24Nm, M10 - 52 Nm, M12 - 80 Nm, M14 - 130 Nm, M16 - 200
Nm Grade 10.9: M12 – 120Nm, M10 – 70Nm M8- 35Nm
Fitting
Instructions
µW0001HN69AU-FIT$011212050000WÄ
W0001HN69AU-FIT$011212050000
TOWBAR
For HONDA CRV 2012-
HN69AU