Parkside PGI 1200 A1 Consignes D'utilisation Et De Sécurité page 8

1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
2. Device description (Fig. 1-12)
1. Handle
2. Fuel tank cap
3. Foot
4. Operating bulb
5. Oil check bulb
6. On/off switch
7. Earthing screw
8. 230 V∼ socket
9. Choke lever
10. Starter grip
11. Air filter lid
12. Air filter
13. Oil filler plug
14. Low oil trip
15. Spark plug cap
16. Spark plug
17. Fuel tap
18. Fuel filter
3. Scope of delivery
• Oil filler bottle (A) (1 pcs.)
• Handle (B) (1 pcs.)
• Screwdriver (C) (1 pcs.)
• Spark plug spanner (D) (1 pcs.)
• Socket wrench (E) (1 pcs.)
• Tool bag (F) (1 pcs.)
• Original Operating Manual (1 Stk.)
4. Intended use
The generator is suitable for devices which use a 230 AC volt-
age source. Please check the suitability for use of house hold
devices on the manufacturer information.
The equipment is allowed to be used only for its prescribed
purpose. Any other use is deemed to be a case of misuse. The
user/operator and not the manufacturer will be liable for any
damage or injuries of any kind resulting from such misuse.
An element of the intended use is also the observance of the
safety instructions, as well as the assembly instructions and op-
erating information in the operating manual.
Persons who operate and maintain the machine must be fa-
miliar with the manual and must be informed about potential
dangers.
In addition, the applicable accident prevention regulations
must be strictly observed.
Other general occupational health and safety-related rules and
regulations must be observed.
The liability of the manufacturer and resulting damages are ex-
cluded in the event of modifications of the machine.
Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty
will be voided if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
GB/IE/NI 3