DocuSign Envelope ID: F7EA4F6B-48A5-4765-B3A2-8870DFE73A5D
The manufacturer herewith declares that the equipment is in conformity with the UK statutory requirements.
(1)
(2)
Equipment type
Applicable
(3)
Directives
Approved body
(9)
(10)
This partly completed machinery must not be put into service until the final machinery in which it is
to be incorporated has been declared in conformity with Supply of Machinery (Safety) Regulations 2008.
Sames is allowed to compil the technical documentation. Sames undertakes to transmit, in response to
a reasoned request by the national authorities, relevant information on the partly completed machinery
in the most appropriate form. This declaration of incorporation of partly completed machinery and this
declaration of conformity are issued under the sole responsibility of the manufacturer.
Director of the STAINS site - Executive Management (EM)
Hervé WALTER
Established in Stains, on 05
Siège Social / Headquarter: 13, chemin de Malacher - CS70086 - 38243 Meylan Cedex - France - Tél / Phone: +33 (0)4 76 41 60 60
The relevant technical documentation was compiled as
(4)
The essential health and safety requirements mentioned in Supply of Machinery
2008 No.
(Safety) Regulations 2008 have been applied.
1597
Articles: 1.1 , 1.1.2 ,1.1.3, 1.1.5 , 1.2 , 1.2.2, 1.2.3, 1.2.4, 1.2.4.1 , 1.2.4.3 , 1.2.6,
1.3 ,1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.6, 1.3.7, 1.3.9, 1.4,1.4.1,1.4.2, 1.4.2.1, 1.5,
1.5.2, 1.5.3, 1.5.4, 1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.6, 1.6.1 , 1.6.2, 1.6.3, 1.6.4, 1.7,
1.7.1, 1.7.2
That partly completed machinery is also in conformity with the provisions of
(5)
Marking
(6)
2016 No. 1107
(7)
Designated
standards
(8)
Conformity
assessment
procedure
CML 2503 - Ellesmere Port - United Kingdom
March 2024
th
SAS au capital de 12.720.000 euros | RCS Grenoble: 572 051 688 | Code APE: 2829B | TVA intracom: FR36 572051688
DECLARATION OF INCORPORATION
OF PARTLY COMPLETED MACHINERY
UK DECLARATION OF CONFORMITY
AIRLESS PUMP 40C50
specified in annex VII, part B.
AIRLESS PUMP 40C50
II 2G Ex h IIB T2 Gb X
AIRLESS PUMPS WITH CUP RANGE
II 2G Ex h IIB T1-T6 Gb X
Ex h => Protection par sécurité de construction (c) /
Protection by constructional safety (c)
Conditions spéciales d'utilisation, le signe X indique de se
référer aux prescriptions figurant dans le manuel d'instructions
qui accompagnent le produit.
- Specific conditions of use, X indicates to refer to the
prescriptions
specified
accompanies the product.
EN ISO 80079-36 : 2016
EN ISO 80079-37 : 2016
EN 1127-1 : 2019
Module A Technical documentation (Annex VIII)
Sames
1
in
the
instructions
manual
DEC UK 578178130
that