SAMES KREMLIN 40C50 AIRLESS Manuel D'instructions page 2

DocuSign Envelope ID: F7EA4F6B-48A5-4765-B3A2-8870DFE73A5D
The manufacturer herewith declares that the equipment is in conformity with the relevant Union harmonization legislation.
(1)
Equipment type
(2)
(3) Applicable Directives
(9) Notified body
(10) This partly completed machinery must not be put into service until the final machinery in which it is to be
incorporated has been declared in conformity with Directive 2006/42/CE on Machinery.
Sames is allowed to compil the technical documentation.
Sames undertakes to transmit, in response to a reasoned request by the national authorities, relevant information
on the partly completed machinery in the most appropriate form. This declaration of incorporation of
partly completed machinery and this declaration of conformity are issued under the sole responsibility of the
manufacturer.
Director of the STAINS site - Executive Management (EM)
Hervé WALTER
Established in Stains, on 05
Siège Social / Headquarter: 13, chemin de Malacher - CS70086 - 38243 Meylan Cedex - France - Tél / Phone: +33 (0)4 76 41 60 60
The essential health and safety requirements mentioned in the Directive 2006/42/CE on
2006/42/CE
Machinery have been applied.
Articles: 1.1 , 1.1.2 ,1.1.3, 1.1.5 , 1.2 , 1.2.2, 1.2.3, 1.2.4, 1.2.4.1 , 1.2.4.3 , 1.2.6,
1.3 ,1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.6, 1.3.7, 1.3.9, 1.4,1.4.1,1.4.2, 1.4.2.1, 1.5, 1.5.2,
1.5.3, 1.5.4, 1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.6, 1.6.1 , 1.6.2, 1.6.3, 1.6.4, 1.7, 1.7.1, 1.7.2
(5) That partly completed machinery is also in conformity with the provisions of
Marking
(6)
2014/34/UE
(7) Harmonised
standards
(8) Conformity
assessment
procedure
INERIS 0080 – 60550 Verneuil-en-Halatte – France – INERIS-EQEN
March 2024
th
SAS au capital de 12.720.000 euros | RCS Grenoble: 572 051 688 | Code APE: 2829B | TVA intracom: FR36 572051688
DECLARATION OF INCORPORATION
OF PARTLY COMPLETED MACHINERY
EU DECLARATION OF CONFORMITY
AIRLESS PUMP 40C50
(4) The relevant technical documentation was compiled
as specified in annex VII, part B.
AIRLESS PUMP 40C50
II 2G Ex h IIB T2 Gb X
AIRLESS PUMPS WITH CUP RANGE
II 2G Ex h IIB T1-T6 Gb X
Ex h => Protection par sécurité de construction (c) /
Protection by constructional safety (c)
Conditions spéciales d'utilisation, le signe X indique de se référer
aux prescriptions figurant dans le manuel d'instructions qui
accompagnent le produit.
- Specific conditions of use, X indicates to refer to the
prescriptions specified in the instructions manual that
accompanies the product.
EN ISO 80079-36 : 2016
EN ISO 80079-37 : 2016
EN 1127-1 : 2019
Module A Technical documentation (Annex VIII)
Sames
1
DEC EU 578178130