Triton TMNPL Instructions D'utilisation Et De Sécurité page 11

1. Rotate the Blade Drum (11) so one Blade (12) faces up and is
accessible.
2. Using the Spanner (8) (Fig. I), loosen the three Blade Clamp
Bolts (14) (Fig. II) just sufficiently to remove the Blade from the
drum.
3. Carefully remove the Blade from the Blade Clamp slot, using a
small piece of wood to push the Blade out (Fig. III).
4. Slide the Blade (12) into the slot in the Blade Clamp (Fig. IV)
so that the point of the Blade edge is closer to the Chamfer
Grooves (15), which then tapers down toward the Base (16)
matching the contour of the Blade Clamp.
5. Ensure that both ends of the Blade are protruding equally (Fig. V).
6. Tighten the Blade Clamp Bolts (Fig. VI).
Note: Do not attempt to adjust the Blade with the Blade Clamp
(13) screws, which are pre-set at manufacturing.
Correct setting of blades
• It is essential that the blades are set correctly or the workpiece
will end up rough and uneven. For a clean, smooth cut, the
blades must be mounted so the cutting edge is absolutely level,
i.e. parallel to the surface of the rear Base (16) (Fig. VII).
Nicks in the surface
• The cutting edge of one or all blades is not parallel to the rear
base (Fig. VIII).
Gouging at start
One or all blades are not protruding enough in relation to the rear
base (Fig. IX).
Adjusting the planing depth
1. Rotate the Depth Adjustment Dial (1) clockwise for a deeper cut
and anticlockwise for a shallower cut.
2. The calibrations on the ring under the Depth Adjustment Dial
indicate the cutting depth. For example, when '1.0' is next
to the point on the front of the planer, the depth of cut is
approximately 1.0mm.
3. If depth of cut is critical, plane a scrap piece of wood, measure
the difference in thickness and adjust the setting as needed.
Using the rear parking rest
• The Rear Parking Rest (7) protects workpieces from damage
when the tool is put aside.
• The rest automatically folds backwards when planing (Fig. X).
Dust/Chip extraction
WARNING: Always use a workshop vacuum, dust/chip extraction
system or the Dust/Chip Bag (17) when operating this tool.
• A workshop vacuum or dust extraction system can be connected
to the side Dust/Chip Extraction Port (2) (Fig. XI).
• The Dust/Chip Bag (17) can be connected to the side Dust/Chip
Extraction Port.
WARNING: NEVER remove obstructions from the Dust/Chip
Extraction Port while the Blades and Blade Drum are rotating.
Always disconnect the tool from the power supply before removing
any obstructions.
Operation
Switching ON & OFF
WARNING: Before plugging the tool into the power socket,
always check that the ON/OFF Trigger Switch (3) and Lock-Off
Button (4) work correctly.
1. Plug the Power Cord (6) into the mains power supply.
2. To power ON, depress the Lock-Off Button (4) and
simultaneously squeeze the ON/OFF Trigger Switch (3).
Note: The Lock-Off Button can be released once the planer is
running.
3. To power OFF, release the ON/OFF Trigger Switch.
WARNING: The planer blades continue to turn for some time
after switching OFF the planer. Wait until the motor has completely
stopped before setting down the tool to prevent damage to the
planer blades or the workpiece surface. If you wish to rest the
planer on its side, do not rest it on the side with the vents, as these
prevent dust or chips from getting into the motor.
When the planer is not to be used for a short period, set the Depth
Adjustment Dial (1) to the '0' position and rest the front of the
plane on a block of wood to keep the base clear of the surface.
Ensure the Rear Parking Rest (7) is down to protect the blades.
Planing
WARNING: Moving the tool too fast may cause a poor quality
cut and can damage the blades or the motor. Moving the tool too
slowly may burn or 'mar' the cut. The proper feed rate will depend
on the type of material being cut and the depth of the cut. Practice
first on a piece of scrap material to gauge the correct motion.
WARNING: Always use two hands to hold the planer.
WARNING: Where possible, clamp the workpiece to a
workbench.
1. Rest the front of the planer on the workpiece, ensuring the
Blades (12) are not in contact with the workpiece.
2. Switch ON the tool and wait for the blades to reach full speed.
3. Move the planer gently forward, applying pressure on the front
of the tool at the start of planing, and pressure at the rear of the
tool towards the end of the planing stroke.
4. Push the planer beyond the edge of the workpiece without
tilting it downwards.
Note: Planing is easier if you incline the workpiece slightly away
from you so that you plane 'downhill' .
5. The rate of planing and the depth of cut determine the quality
of the finish. For rough cutting, you can increase the depth of
cut; however, to achieve a good finish, you need to reduce the
depth of cut and advance the tool more slowly.
6. Lift the tool from the workpiece before releasing the ON/OFF
Trigger Switch and powering OFF.
7. In between operations, rest the planer on a flat surface with the
Rear Parking Rest (7) to support the planer, so that the blades
are kept clear of the surface of the workpiece.
Chamfering
1. To make a chamfered cut (Fig. XII), align the required size 'V'
Chamfer Groove (15) in the front base of the planer with the
corner edge of the workpiece.
EN
11