Publicité
Les langues disponibles
Les langues disponibles
14 | English
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Hammer Safety Warnings
Safety instructions for all operations
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring or its
own cord. Cutting accessory or fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Safety instructions when using long drill bits with rotary
hammers
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure. Bits can bend, causing
breakage or loss of control, resulting in personal injury.
Additional Safety Information
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
1 609 92A 9EX | (13.05.2024)
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Do not touch any application tools or adjacent housing
u
components shortly after operation. These can become
very hot during operation and cause burns.
The application tool may jam during drilling. Make
u
sure you have a stable footing and hold the power tool
firmly with both hands. Otherwise you could lose con-
trol of the power tool.
Take care when carrying out demolition work using
u
the chisel. Falling fragments of the demolition material
could injure you or any bystanders.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for hammer drilling in concrete,
brick and stone, as well as for light chiselling work. It is also
suitable for drilling without impact in wood, metal, ceramic
and plastic. Power tools with electronic control and right/left
rotation are also suitable for screwdriving.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
a)
(1)
Keyless chuck
SDS plus drill chuck
(2)
(3)
SDS plus tool holder
(4)
Dust protection cap
(5)
Locking sleeve
(6)
Lock-on button for on/off switch
(7)
On/off switch
(8)
Rotational direction switch
(9)
Release button for impact/mode selector switch
(10)
Impact/mode selector switch
Bosch Power Tools
Publicité
