Publicité
Les langues disponibles
Les langues disponibles
k) Do not operate the machine while people, especially
children, are nearby.
l) Do not use the machine in daylight or good artificial
light.
m) Before using the machine and after any impact, check
for signs of wear or damage and if necessary to carry out
the necessary repairs.
n) Do not operate the machine if the cutter is damaged or
shows excessive wear.
o) Do not operate the machine if it has protective
damaged or are not in place.
p) Always keep hands and feet away from cutting devices
and more particularly when starting the engine
q) Always make sure the handles and guards are fitted
when the machine is being used. Never attempt to use an
incomplete machine or subjected to unauthorized
modification.
r ) Never use replacement parts or accessories not
supplied or recommended by the manufacturer .
s) Turn off the engine and remove the spark plug wire
before performing any checks or maintenance work on
the machine when not in use.
t) Always make sure the vents are free of debris.
u) Do not operate the machine near , liquid or flammable
or explosive gas . Never operate the machine in enclosed
or poorly ventilated areas , because once turned on, the
engine produces toxic exhaust gases. These gases are
odorless and invisible , and therefore dangerous . In
addition, if they are inhaled , these gases can cause
unconsciousness and even death.
v) Wear suitable work clothes. Do not wear loose clothing
or jewelry that can get caught in moving parts of the
machine. Always wear safety goggles or other eye
protection, hearing protection (MANDATORY when the
sound pressure exceeds 80 dB (A)), a helmet (it is
recommended to wear a helmet with face protection ),
boots or shoes with non-slip soles, long and robust and
resistant gloves work pants. Equipment (PPE) used must
meet the standards.
2. Tips for using the machine trimmer function
a) At the start of the engine when it is running, keep body
parts, especially hands and feet away from the cutting
blade and 3 teeth. Do not start the trimmer when she
returned (his head in the air) or if it is not in the correct
working position.
The guard and other protective devices are designed
to protect you but also to ensure proper operation of
the device.
b) Use only with a cutting head and a blade 3 original
teeth. Never use metal cutting body instead of plastic
wire. Do not use the machine for cutting grass / grass that
does not grow in soil, for example grass on walls,
rockeries, over the head, etc.. With the unit, do not cross
areas and stony paths.
After switching off the machine, blade and nylon
thread still running for a few seconds, so be very
careful.
c) Maintain a safe distance of 15 m around the trimmer in
use . In the work area , the user is responsible trimmer
vis- à-vis accidents and damage to others or Their
property by the use of the device. Stop the engine while
using people , Especially children, or pets are nearby .
d) Do not touch area around the muffler or cylinder, All
which hot Become falling on use.
e) Hold the brushcutter with the right hand on the trigger
handle and the left hand on the forehead handle. Firmly
hold the handles falling on operation . The trimmer
shoulds be Held in a comfortable position with the rear
handle about hip height .
f) Always use the trimmer at full throttle . Cut tall grass
from the top down . This Will Prevent grass from
wrapping around the tube of the motor shaft and the
cutting head , Could All which causes damage due to
Overheating .
If grass Becomes wrapped around the cutting head , stop
the engine, disconnect the spark plug wire and remove
the grass . Prolonged half- throttle Will result in oil
dripping from the exhaust .
3 . Causes and prevention of rebounds by the
operator when using the 3 blade teeth
When fitted with a blade, use this tool with extreme
caution. A rebound blade can occur when it comes into
contact with an object it can not cut . This contact can
cause a short blade lock , which "bounce" the tool in the
opposite direction of the struck object . This can be quite
violent and lose control of the tool. To facilitate cutting
and security , working with a movement from right to left .
To avoid kickback , observe the safety instructions below
63
Publicité
