Bosch AQT 45-14 X Notice Originale page 15

OBJ_BUCH-2164-006.book Page 15 Thursday, October 27, 2016 7:52 AM
Noise/Vibration Information
Sound emission values determined according to EN 60335-2-79.
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to
h
EN 60335-2-79:
Vibration emission value a
h
Uncertainty K
Mounting and Operation
Action
Delivery Scope
Adjusting the Handle
Connecting high pressure gun to lance 3
Connecting high pressure water supply
hose/nozzle
Attaching Nozzle
Connecting to the water supply
Switching On and Off
Clean the water filter
Clean nozzle
Gun storage
Gun/lance/nozzle is stored in action
Hose into the hose holder
Storage
Selecting Accessories
Starting
For Your Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Only use approved exten-
sion cables. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
– 1.5 mm – max length 20 m
2
– 2.5 mm – max length 50 m
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
Bosch Power Tools
Figure Page
1 252
Cable connections should be kept dry and off the ground.
2 253
For increased electrical safety use a Residual Current Device
254
(RCD) with a tripping current of not more than 30 mA. Always
check your RCD every time you use it.
4 255
If the supply cord is damaged, it must be replaced by a Bosch
5 256–257 Service Centre.
For products not sold in GB:
6 257
WARNING: For your safety, it is required that the plug at-
7 258
tached to the machine is connected with the extension cord.
8 258
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
9 258
extension cord must be used with a cable strain relief.
10 259
To prevent damage to the appliance, do not allow it to operate
11 259
dry.
12 260
Products sold in GB only: Your product is fitted with a
13 260 BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
14 261
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Operation
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and water
supply hose. Release trigger. Press the safety lock (front but-
ton on the gun handle).
3 600 ... HA7 3..
dB(A)
dB(A)
dB
2
m/s
2
m/s
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
F 016 L81 380 | (27.10.16)
English | 15
HA7 4..
81 81
94 94
2 2
2.0 2.0
1.5 1.5