Kenwood KM260 Serie Manuel D'instructions page 8

Food Processor AT284
Use the food processing attachment to chop, slice, shred and rasp. The citrus
juicer attachment (if supplied) can be used to juice citrus fruit and can only be
used with the AT284 food processor.
important
When removing the packaging, ensure the plastic blade cover is removed
from the knife blade. Take care the blades are very sharp. The cover
should be discarded as it is to protect the blade during manufacture and
transit only.
safety
The blades and discs are very sharp, handle with care. Always hold the
G
knife blade by the finger grip at the top, away from the cutting
edge, both when handling and cleaning.
Always remove the knife blade before pouring contents from the bowl.
G
Keep hands and utensils out of the processor bowl whilst connected to the
G
power supply.
G Never use your fingers to push food down the feed tube. Always use the
pusher/s supplied.
Before removing the lid from the bowl or the attachment from the power
G
unit:-
switch off;
G G
wait until the blades/discs have completely stopped;
G G
When slicing/shredding or rasping don't let the bowl fill up as far as the
G
cutting disc: empty it regularly.
G Should excessive vibration occur when using this attachment, either reduce
the speed or stop the machine and remove some of the contents.
This machine will be damaged and may cause injury if the
G
interlock mechanism is subjected to excessive force.
key
&
food processor
pushers: large and small
feed tube
food processor lid
finger grip
knife blade
food processor bowl
drive shaft
thick slicer/shredder disc
thin slicer/shredder disc
rasping disc
optional discs
thin (julienne style) chipper disc
standard chipper disc
extra coarse shredding disc
citrus juicer
cone
sieve
Not all of the above parts will necessarily be included in pack. Contents are
dependent upon model variant.
knife blade
Use the knife blade to chop raw and cooked meat, cooked eggs,
vegetables, nuts, pâtés and dips and to also make crumbs from bread and
biscuits.
to use the knife blade
1 Remove the medium speed outlet cover by lifting off
2 Place the drive shaft onto the outlet
3 Fit the bowl over the drive shaft with the handle above the on/off and speed
switch and turn clockwise until it locks into position
4 Fit the knife blade over the drive shaft and turn until it drops all the way down.
The knife blade is very sharp always handle with care.
5 Cut the food up and place into the bowl ensuring that it is evenly distributed.
6 Fit the lid, feed tube above the speed switch and turn clockwise ensuring
that the tab on the lid slots into the groove in the bowl handle
correctly fitted the markings should align
The attachment will not operate if it is incorrectly assembled
G
or incorrectly fitted to the kitchen machine or if the high
speed outlet cover is not fitted.
7 Fit the pushers.
(if supplied)
.
.
.
. When
.
8 Switch on and process until the desired consistency is achieved. We
recommend a high speed for most chopping functions.
Use the pulse for short burst of power. The pulse will operate for as long
G
P P
as the switch is held in position.
9 Switch off and unplug.
10 Remove the attachment.
11 Refit the medium speed outlet cover after use.
hints
Cut food up before placing into the bowl. Meat, bread, vegetables and other
G
foods of a similar texture should be cut into cubes approximately 2cm/3⁄4 in.
Biscuits should be broken into pieces and added down the feed tube whilst
the machine is operating.
Herbs are best chopped when clean and dry.
G
G Don't blend liquid ingredients as they may leak from around the lid. A
blender is available for this purpose. However, when puréeing soups etc.,
drain solids, blend and then return to the liquid.
Take care not to over process when using the knife blade.
G
Don't use the knife blade to mix heavy loads such as bread dough otherwise
G
you may damage the mixer. Use the dough hook in the mixing bowl to make
bread and the beater in the bowl to make cakes and pastry.
Don't use the knife blade to chop ice cubes or other hard foods, such as
G
spices, they may damage the attachment.
If adding almond essence or flavouring to mixtures avoid contact with the
G
plastic as this may result in permanent marking.
maximum capacity
meat 400g (14oz)
G
Make 'mince' by trimming raw meat of any excess fat and cutting into
2 cm/ 3 ⁄ in cubes, place into the processor bowl and operate for
4
approximately 20 seconds or until the desired texture is achieved. The longer
you run the machine the smoother the texture will be.
slicer/shredder and rasping disc
Use the slicer/shredder to slice or shred fruit, vegetables and cheese and
the rasping disc for grating Parmesan cheese and potato for German potato
dumplings.
to use the slicer/shredder/rasper
what the cutting discs do
slicer/shredders
Discs and are reversible: one side slices, the other side shreds. You
can slice cheese, carrot, potato, cabbage, cucumber, courgette, beetroot,
onion. You can shred cheese, carrot, potato and foods of a similar texture.
Your chosen cutting side must be uppermost.
rasping disc grates parmesan cheese and potato for German potato
dumplings.
optional discs
thin (julienne style) chipper
This disc cuts potatoes for Julienne style French fries and firm ingredients for
salads, garnishes, casseroles and stir fries (eg carrot, swede, courgette and
cucumber).
standard chipper cuts potatoes for thin French fries and firm
ingredients for salads and dips (eg swede, cucumber).
extra coarse shredder
using the cutting discs
1 Remove the medium speed outlet cover by lifting off.
2 Place the drive shaft onto the outlet.
3 Fit the bowl over the drive shaft with the handle above the on/off and speed
switch and turn clockwise until it locks into position.
4 Place the cutting disc onto the drive shaft. Your chosen cutting side must be
uppermost. Handle the cutting discs with care - they are
extremely sharp. Hold the discs by the centre grip.
5 Fit the lid, feed tube above the speed switch and turn clockwise ensuring
that the tab on the lid slots into the groove in the bowl handle. When
correctly fitted the markings should align
The attachment will not operate if it is incorrectly assembled
G
or incorrectly fitted to the kitchen machine or if the high
speed outlet cover is not fitted.
6 Choose which feed tube you want to use. The pusher contains a smaller
feed tube for processing individual items or thin ingredients.
6
coarsely shreds cheese and carrot.
.