Louisiana Grills LG700 Assemblage Et Fonctionnement page 24

Grill Produces Grease Build-Up
Excess Or
Wood Pellet Quality
Discolored
Smoke
Burn Grate Is Blocked
Insufficient Air Intake
For Fan
Grill Will Not Control Settings
Achieve Or
Maintain Stable
Temperature
Insufficient Air Flow
Through Burn Grate
Lack Of Fuel, Poor Fuel
Quality, Obstruction In
Feed System
Grill Probe
"Er-1" Error Code The Unit Has
Overheated, Possibly
Due To Grease Fire Or
Excess Fuel.
Grill Probe Is Not
Making A Connection
"Er-2" Error Code Grills Fails To Perform
Start-Up Cycle
Grill Will Not Stay Lit
"Er-3" Error Code Power Interruption
While In Operation
Power Outage While
Unit In Operation.
"noPr" Error Code Bad Connection At
Connection Port
Meat Probe Damaged Check for signs of damage to the wires of the meat probe. If damaged, call Customer Service
24
Follow Care and Maintenance instructions.
Remove moist wood pellets from hopper. Follow Care and Maintenance instructions to
clean out. Replace with dry wood pellets.
Clear burn grate of moist wood pellets. Follow Hopper Priming Procedure.
Check fan. Ensure it is working properly and air intake is not blocked. Follow Care and
Maintenance instructions if dirty.
Check the Digital Control Center to ensure that the small LED is next to the ACTUAL
temperature. If not, press the TEMP display touch pad to indicate which temperature is
presently being displayed.
Grill is unable to function properly. Follow Set-Up Procedure to ensure proper positioning of
cooking components. Check burn grate for proper positioning. Follow Care and Maintenance
instructions for ash build-up. Check that the air intake for the fan is not blocked. If no
blockage, remove hopper access panel (see Electric Wire Diagram for diagram) and locate
the blue and white fan wires. Ensure that connection is tight by lightly tugging on each wire.
If loose, push back into connector until it clicks. Check fan blades for cleanliness. Check grill
probe. Follow Care and Maintenance instructions if dirty. Check hopper for an obstruction
in the feed system. Remove pellets and follow Care and Maintenance instructions. Once
maintenance is done, perform a test. With cooking components removed, press the Power
Button to turn the unit on. Check that the igniter in the burn grate is bright and vibrant.
Replace cooking components into grill and use as normal.
Check hopper to check that fuel level is sufficient, and replenish if low. Should the quality of
wood pellets be poor, or the length of the pellets too long, this may cause an obstruction in
the feed system. Remove pellets and follow Care and Maintenance instructions.
Check status of grill probe. Follow Care and Maintenance instructions if dirty. Contact
Customer Service for a replacement part if damaged.
Press the Power Button to turn the unit off, and allow grill to cool. Follow Care and
Maintenance instructions. After maintenance, remove pellets, and confirm positioning of
all component parts. Once cooled, press the Power Button to turn the unit on, then select
desired temperature. If error code still displayed, contact Customer Service.
Check for damage to the grill probe. Follow Care and Maintenance instructions if dirty. If
all appears in working order, check the connection to the Digital Control Center. Unplug unit
from power source. Remove hopper access panel (see Electric Wire Diagram for diagram).
Locate the silver and brown wires of the grill probe. Disconnect the spade connectors, then
reconnect until it clicks. Replace the hopper access panel.
Grill is unable to function properly. Follow Set-up Procedure instructions. Check hopper for
sufficient fuel or if there is an obstruction in the feed system. Remove pellets and follow
Care and Maintenance instructions. Check grill probe. Confirm if ACTUAL temperature
is correct and accurate. Follow Care and Maintenance instructions if dirty. Check igniter
positioning and that it is heating up properly. In extreme cold, the grill may require a second
start. Turn grill off, wait, then turn on again. Check fan. Ensure it is working properly. Follow
Care and Maintenance instructions if dirty.
Power source was interrupted, and the grill did not complete its cool-down cycle. Check
power supply; there may have been a power outage during use. Press the Power Button to
turn the unit off, wait two minutes, then press the Power Button to turn the unit on again.
If error code still displayed, contact Customer Service.
Disconnect meat probe from connection port on the Digital Control Center, and reconnect.
Ensure the meat probe adapter is firmly connected.
for replacement part.