Abit IP35 Pro Manuel D'utilisation

Masquer les pouces

page de 88

/ 88
Signets

Liens rapides

Télécharger ce manuel

IP35 Pro

Motherboard

Socket 775

User's Manual

About this Manual:

This user's manual contains all the information you may

need for setting up this motherboard. To read the user's

manual of PDF format (readable by

the "Driver & Utility CD" into the CD-ROM drive in your

system. The auto-run screen will appear, click the

"Manual" tab to enter its submenu. If not, browse the

root directory of the CD-ROM via the File Manager, and

double click the "AUTORUN" file.

Adobe

Reader), place

Intel P35 / ICH9R

FSB 1333 MHz

Dual Channel DDR2 800

Dual PCI-E X16 Slots

Dual Gigabit LAN

6x Internal, 2x External SATA

3Gb/s Connectors

USB 2.0 / IEEE 1394

7.1-Channel HD Audio

abit uGuru™ Technology

abit Silent OTES™ Technology

External CMOS Clearing

Switch

Quick Power & Reset Button

Vista Premium HW Ready

Sommaire des Matières pour Abit IP35 Pro

Page 1 3Gb/s Connectors USB 2.0 / IEEE 1394 7.1-Channel HD Audio abit uGuru™ Technology abit Silent OTES™ Technology About this Manual: External CMOS Clearing This user’s manual contains all the information you may need for setting up this motherboard. To read the user’s...
Page 2 IP35 Pro User’s Manual English + Multilingual QIG P/N: 4310-0000-77 Rev. 1.00, April 2007 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.
Page 3 2. BIOS Setup............... 2-1 ™ 2.1 μGuru Utility ................2-2 2.1.1 OC Guru ................2-2 2.1.2 ABIT EQ................2-4 2.2 Standard CMOS Features............2-10 2.3 Advanced BIOS Features ............2-13 2.4 Advanced Chipset Features............2-16 2.5 Integrated Peripherals ..............2-17 2.6 Power Management Setup ............
Page 4 3.5 LAN Driver................... 3-4 3.6 JMicron SATA Driver..............3-4 3.7 USB 2.0 Driver ................3-4 3.8 abit μGuru ................... 3-5 3.9 SATA RAID Driver (for Windows Vista) .......... 3-6 3.10 SATA RAID Driver (for Windows XP, 2003, or 2000) ..... 3-6 4.
Page 5 Intel ICH9R support Intel ™ • abit uGuru Technology Matrix Storage Tech (AHCI & RAID 0, 1, ™ • abit Silent OTES Technology 5, and 10). • External CMOS Clearing Switch • 2x External SATA 3Gb/s connectors offered by JMicron JMB363 support •...
Page 6 1.2 Motherboard Layout IP35 Pro...
Page 7 Install the motherboard with screws and have them tightened. To prevent shorting the PCB circuit, ※ please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mounting-holes on the motherboard to align with. IP35 Pro...
Page 8 “EZ-CCMOS1”, see the section of “Connecting Rear Panel I/O Devices” in this manual for detail. The C.C. POST Code appears when either the external “EZ-CCMOS1” switch or ※ the internal “CCMOS1” jumper is not set to its normal position. IP35 Pro...
Page 9 CAUTION: Danger of explosion may arise if the battery is incorrectly renewed. ※ Renew only with the same or equivalent type recommended by the battery ※ manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions. ※ IP35 Pro...
Page 10 EPS12V power source to meet the 240VA Plugged from a 4-pin Plugged from an 8-pin protection limits. ATX12V power. EPS12V power. [ATX4P1]: Auxiliary 12V power connector This connector provides an auxiliary power source for devices added on PCI Express slots. IP35 Pro...
Page 11 Please refer to the BIOS setup route: “PC Health Status” “ABIT FanEQ Control” “CPU FAN Type” to select the one of your own. These fan connectors are not jumpers. DO NOT place jumper caps on these ※...
Page 12 2. Use your right-thumb to raise the load 4. Visually inspect if the CPU is seated well plate. Lift it up to fully open position. into the socket. The alignment key must be located in the notch of package. IP35 Pro...
Page 13 7. Secure the lever with the hook under retention tab. A higher fan speed will be helpful for better airflow and heat-dissipation. ※ Nevertheless, stay alert to not touch any heatsink since a high temperature generated by the working system is still possible. IP35 Pro...
Page 14 DIMM module. Static electricity can damage the electronic components of the computer or ※ optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly. 1-10 IP35 Pro...
Page 15 Make sure to configure the “Master” and “Slave” relation before connecting ※ two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. IP35 Pro 1-11...
Page 16 SATA device and connect the other end from the power supply. The motherboard in this photo is served for DEMO only, and may not be the ※ same type or model as the one described in this user’s manual. 1-12 IP35 Pro...
Page 17 I/O panel or the front-mounted IEEE 1394 port of your chassis. Pin Assignment Pin Assignment TPA0 + TPA0 - Ground Ground TPB0 + TPB0 - +12V +12V Ground Make sure the connecting cable bears the same pin assignment. ※ IP35 Pro 1-13...
Page 18 Pin 4 “AVCC” of this header. Pin Assignment Pin Assignment (HD AUDIO) (AC’97 AUDIO) MIC2 L MIC In AGND MIC2 R MIC Power AVCC FRO-R Line Out (R) MIC2_JD F_IO_SEN FRO-L Line Out (L) LINE2_JD 1-14 IP35 Pro...
Page 19 The audio driver is originally configured to support HD Audio. For AC’97 audio connection, you may: Right-click the “Realtek HD Audio Manager” icon system tray. Click “Audio I/O” tab, and then click “Connector Settings”. Click “Disabled front panel jack detection”, and then click “OK” to confirm. IP35 Pro 1-15...
Page 20 It is not recommended to install only one PCI Express graphics card on the ※ [PCIEXP2] slot, for such will pull the speed down to x4 only. Install PCI Express X1 cards into slot “PCIE1”. Install PCI cards into slots “PCI1”, “PCI2”, and/or “PCI3”. 1-16 IP35 Pro...
Page 21 1.8.9 Guru Panel Connection Header This header is reserved for connecting abit’s exclusive Guru Panel. For more information, please refer to the included Guru Panel Installation Guide. IP35 Pro 1-17...
Page 22 POST Code in address 80h to find out where the problem lies. This LED device also displays the “POST” Code of AC2005, an “uGuru” chipset developed exclusively by abit. The decimal point lights up during the AC2005 POST action.
Page 23 3VSB: This LED lights up when the power supply is connected with power source. • VCC: This LED lights up when the system power is on. 1.9.3 Onboard Buttons • PWRSW1: Push this button to power on the system. • RESET1: Push this button to reset the system. IP35 Pro 1-19...
Page 24 Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. • LAN1/LAN2: Connects to Local Area Network. • USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. 1-20 IP35 Pro...
Page 25 In order to increase system stability and performance, our engineering staff is ※ constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen. IP35 Pro...
Page 26 External Clock This item selects the external clock frequency. Due to the specification limit of the CPU you installed, the speed you set over its standard bus speed is supported, but not guaranteed. IP35 Pro...
Page 27 This item selects the voltage for DDR2 memory modules. CPU VTT Voltage This item selects the VTT voltage for CPU. MCH 1.25V Voltage This item selects the voltage for MCH (NB). ICH 1.05V Voltage This item selects the Core voltage for ICH (SB). IP35 Pro...
Page 28 :Move Enter:Select +/-/PU/PD:Value F8:OC On The Fly F10:Save ESC:Exit These items display the power cycle statistics for each element. 2.1.2 ABIT EQ Click right-arrow <→> key to switch from OC Guru setup menu to ABIT EQ setup menu: μGuru Utility v1.01C ABIT EQ...
Page 29 ABIT EQ Beep Control This item controls if the beeper sounds or not when any warning event occurred. Temperature Monitoring Click <Enter> key to enter its submenu: μGuru Utility v1.01C ABIT EQ Temperature Monitoring Reading Shutdown Shutdown Beep Beep Enable Temp.
Page 30 Use <Space> key to enable warning beeps function. If the voltage of corresponding element is higher/lower than the high/low limit, warning beeps will sound. High/Low Limit These items set the high and low voltage limit. The high limit voltage must be set higher than the low limit voltage. ※ IP35 Pro...
Page 31 Beep Enable Use <Space> key to enable warning beeps function. If the fan speed is lower than the low limit value, warning beeps will sound. Low Limit These items set the low limit of fan speed. IP35 Pro...
Page 32 When set to [Enabled], these items control the CPU, SYS, and/or AUX1 fan speed by the following setting combinations. Reference Temperature This item selects the reference point for taking temperature among the available options of CPU, SYS, and PWM Temperature. IP35 Pro...
Page 33 These items set the high and low temperature limit that you want to do the fan speed control. DC Fan Voltage High/Low These items set the high and low voltage limit that you want to provide the fan with. The high limit voltage must be set higher than the low limit voltage. ※ IP35 Pro...
Page 34 HDD Auto-Detection Press Enter Item Help SATA Channel 1 Auto Access Mode Auto Capacity 0 MB Cylinder Head Precomp Landing Zone Sector :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults 2-10 IP35 Pro...
Page 35 This item determines whether the system stops if an error is detected during system boot-up. [All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error. [No Errors]: The system-boot will not stop for any error detected. IP35 Pro 2-11...
Page 36 640K for systems with 640K or more memory size installed on the motherboard. Extended Memory This item displays the amount of extended memory detected during system boot-up. Total Memory This item displays the total memory available in the system. 2-12 IP35 Pro...
Page 37 F7: Optimized Defaults Thermal Control This option enables or disables the thermal monitoring. Limit CPUID MaxVal When set to [Enabled], this item limits the CPUID maximum value to 3, which is usually required for older OS like Windows NT4.0. IP35 Pro 2-13...
Page 38 Quick Power On Self Test When set to [Enabled], this item speeds up the Power On Self Test (POST) after powering on the system. The BIOS shorten or skip some check during the POST. 2-14 IP35 Pro...
Page 39 When set to [Yes], this item allows you to run some older operating system without floppy disk drive. Leave this item at its default setting. Full Screen LOGO Show This item determines to show the full screen logo when booting. IP35 Pro 2-15...
Page 40 This item selects the mode for PCI Express add-on card. PEG Force X1 When set to [Enabled], this item forces the PEG port down to x1 mode. Init Display First This item allows you to choose the primary display card. 2-16 IP35 Pro...
Page 41 This item selects the mode for devices connected through SATA1~SATA6 ports. [IDE]: The on-chip Serial ATA served as IDE mode. [RAID]: The on-chip Serial ATA served as RAID mode. [AHCI]: The on-chip Serial ATA served as AHCI (Advanced Host Controller Interface) mode for advanced performance and usability. IP35 Pro 2-17...
Page 42 :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults USB Functions This option enables or disables the USB controller. USB 2.0 Operation Mode This option selects the speed mode for USB devices. 2-18 IP35 Pro...
Page 43 This item allows you to use the boot ROM (instead of a disk drive) to boot up the system and access the local area network directly. Storage Controller This option enables or disables the JMB363 controller that controls both IDE1 and eSATA1 ports. Controller Mode This item selects the mode for devices connected through eSATA1 ports. IP35 Pro 2-19...
Page 44 Options: [IDE], [RAID], [AHCI]. Back to Integrated Peripherals Setup Menu Onboard FDC Controller This option enables or disables the floppy disk controller. 2-20 IP35 Pro...
Page 45 Soft-Off condition. The PCI card must support the wake up function. Wake Up by Onboard LAN1/LAN2 When set to [Enabled], access through the onboard LAN1/LAN2 port can remotely wake up the system that was in Soft-Off condition. IP35 Pro 2-21...
Page 46 Restore On AC Power Loss This item selects the system action after an AC power failure. [Power Off]: When power returns after an AC power failure, the system’s power remains off. You must press the Power button to power-on the system. 2-22 IP35 Pro...
Page 47 If the system’s power is off when AC power failure occurs, it will remain off when power returns. If the system’s power is on when AC power failure occurs, the system will power-on when power returns. IP35 Pro 2-23...
Page 48 This item sets each system interrupt to either [PCI Device] or [Reserved]. PCI/VGA Palette Snoop This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not. [Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA. [Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA. 2-24 IP35 Pro...
Page 49 This option protects the BIOS configuration or restricts access to the computer itself. 2.11 Save & Exit Setup This option saves your selections and exits the BIOS setup menu. 2.12 Exit Without Saving This option exits the BIOS setup menu without saving any changes. IP35 Pro 2-25...
Page 50 2-26 IP35 Pro...
Page 51 • [Utility]: Click to enter the utilities installation menu. • [abit Utility]: Click to enter the installation menu of utilities exclusively developed by abit. • Browse CD]: Click to browse the contents of this “Driver-&-Utility CD”. • Close]: Click to exit this installation menu.
Page 52 SATA Mode Select “RAID”. To install this program: Click on the [Drivers] tab in the installation menu screen. Click the [Intel Matrix Storage Technology Driver] item. The installation screen appears. Follow the prompts on the screen to complete installation. IP35 Pro...
Page 53 Click item “Sound Manager”. The Realtek HD Audio Manager appears. Click the [Audio I/O] tab. Click the pull down menu to select the channel configuration. Click [OK] button to apply the Audio I/O settings and exit. IP35 Pro...
Page 54 Follow the prompts on the screen to complete installation. 3.7 USB 2.0 Driver There is no need to install this driver for Windows 2000 with Service Pack 4, ※ Windows XP with Service Pack 1, or their later version. IP35 Pro...
Page 55 Internet or office applications in full screen with no need to stop or close the running application. To install this utility: Click on the [abit Utility] tab in the installation menu screen. Click the [abit uGuru] item. The following screen appears.
Page 56 Save this selection and exit BIOS setup menu by accessing the BIOS menu “Save & Exit Setup”. Restart the system. The system will now boot from CD, and enter the ABIT Boot Manager, the following options appear (0) Boot From First HDD...
Page 57 • [SLED]: Connecte au câble de la DEL de veille. l’installation de votre carte mère abit. Pour des opérations plus • [PWR]: Connecte au câble de l’interrupteur de l’alimentation avancées, vous devez vous reporter à la version complète.
Page 58 Diese “Kurze Installationsanleitung” enthält nur die Anschlüsse auf der Vorderseite: [FPIO1] grundlegenden Hardwareinformationen, die Sie zur [HLED]: Kabelanschluss für Festplattenzugriffsanzeige. • Installation Ihres abit-Motherboards benötigen. Details [RST]: Kabelanschluss für Rücksetzschalter. • finden Sie im ausführlichen Handbuch. [SPKR]: Kabelanschluss für Kabelanschluss für •...
Page 59 • [PLED]: collega al cavo LED alimentazione. le informazioni di base sull’hardware necessarie all’installazione della scheda madre abit. Fare riferimento Collettore porta USB aggiuntiva: [FP-USB1], [FP-USB2] alla versione completa della guida per eseguire le Collettore porta IEEE 1394 aggiuntiva: [FP-1394-1], [FP-1394-2] operazioni avanzate.
Page 60 [PWR]: Conecte el cable del interruptor de encendido. • durante la instalación de la placa base abit. Para conocer el [PLED]: Conecte el cable del LED de encendido. • funcionamiento avanzado, es necesario consultar la Terminal de puerto USB adicional: [FP-USB1], [FP-USB2] versión completa.
Page 61 à • [PWR]: Faz a ligação ao cabo do botão de alimentação. instalação da sua placa principal abit. Para mais • [PLED]: Faz a ligação ao cabo do LED do botão de alimentação.
Page 62 основная информация о техническом обеспечении, которая • [PLED]: Соединяется с кабелем индикатора питания. вам может понадобиться при установке материнской платы abit. Описание дополнительных операций вы найдете в Дополнительная насадка порта USB: [FP-USB1], [FP-USB2] полной версии руководства. Дополнительная насадка порта IEEE 1394: [FP-1394-1], [FP-1394-2] Предостережения...
Page 63 4.7 Eesti//Kiirpaigaldusjuhend Käesolev “Kiirpaigaldusjuhend” sisaldab ainult [SLED]: Ühendage peatusindikaatori (Suspend LED) • abit-emaplaadi paigaldamiseks vajalikku riistvaraalast kaabliga. põhiteavet. Edasijõudnud kasutamiseks tuleb teil ikkagi [PWR]: Ühendage toitelüliti kaabliga. • pöörduda täisversiooni poole. [PLED]: Ühendage toiteindikaatori (Power LED) kaabliga. • Täiendav USB-pordi päis: [FP-USB1], [FP-USB2] Ettevaatusabinõud riistvara paigaldamisel...
Page 64 4.8 Latviski//Ātrās instalēšanas instrukcija Šī “Ātrās instalēšanas instrukcija” ietver tikai pamata [RST]: Pievieno atiestates slēdža kabeli. • norādes iekārtai, kas nepieciešamas, instalējot abit [SPKR]: Pievieno sistēmas skaļruņa kabeli. • mātesplati. Pilnīgākai darbībai nepieciešams iegūt [SLED]: Pievieno LED pārtraukšanas kabeli. •...
Page 65 [SLED]: Sujunkite su darbo pristabdymo indikatoriaus • informacija apie techninę įrangą, kurios jums gali prireikti kabeliu. instaliuojant pagrindinę plokštę abit. Papildomų operacijų [PWR]: Sujunkite su maitinimo tinklo jungiklio kabeliu. • aprašymą rasite pilnoje vadovo versijoje. [PLED]: Sujunkite su maitinimo indikatoriaus kabeliu.
Page 66 [SLED]: Podłączenie kabla diody LED wstrzymania pracy. • podstawowe informacje dotyczące sprzętu, wymagane [PWR]: Podłączenie kabla przełącznika zasilania. • podczas instalacji płyty głównej abit. Przy [PLED]: Podłączenie kabla diody LED zasilania. • zaawansowanych operacjach, niezbędne będzie skorzystanie z kompletnej wersji instrukcji.
Page 67 4.11 Magyar//Gyorstelepítési útmutató Ez a “Gyorstelepítési útmutató” csak azt az alapvető [PWR]: Csatlakoztassa a tápkapcsoló kábelhez. • hardver információt tartalmazza, amely az abit alaplap [PLED]: Csatlakoztasson a táp LED kábelhez • telepítéséhez szükséges. Az előrehaladott üzemeltetéshez, Kiegészítő USB port fejrész: [FP-USB1], [FP-USB2] továbbra is a teljes útmutatót kell használnia.
Page 68 4.12 Türkçe//Hızlı Kurulum Kılavuzu Bu “Hızlı Kurulum Kılavuzu”, abit anakartınızı takmanızda Ön Panel Konnektörleri: [FPIO1] gerekebilecek sadece temel donanım bilgisini içermektedir. [HLED]: Sabit Disk Sürücü LED kablosuna bağlayın. • İleri işlemler için daha geniş olan tam versiyonuna [RST]: Sıfırlama Anahtarı kablosuna bağlayın.
Page 69 ‫دﻟﻴﻞ اﻟﺘﺮآﻴﺐ اﻟﺴﺮﻳﻊ‬ ‫اﻟﻠﻐﺔ اﻟﻌﺮﺑﻴﺔ‬ 4.13 IP35 Pro 4-13...
Page 70 ‫راهﻨﻤﺎﯼ ﻧﺼﺐ ﺳﺮﻳﻊ‬ ‫ﻓﺎرﺳﯽ‬ 4.14 4-14 IP35 Pro...
Page 71 AUDIO1: 7.1ch オーディオ入力/出力コネクター。 ATX 電源装置: [ATXPWR1]、[ATX12V1] • IEEE 1394: IEEE 1394 プロトコルのデバイスに接ファンコネクタ: [CPUFAN1], [SYSFAN1], [AUXFAN1], 続します。 [NBFAN1] • LAN1: 構内通信網(LAN)に接続します。 • USB1/USB2: スキャナ、デジタルスピーカー、モニ前面パネルコネクタ: [FPIO1] タ、マウス、キーボード、ハブ、デジタルカメラ、ジ • [HLED]: HDD LED ケーブルに接続ョイスティックなどの USB デバイスに接続します。 • [RST]: リセットスイッチケーブルに接続 IP35 Pro 4-15...
Page 72 4.16 한국어//빠른 설치 가이드 본 “빠른 설치 가이드”는 빅빔 abit 메인보드 • [SPKR]: 시스템 스피커 케이블에 연결하세요. • [SLED]: 유휴(Suspend) LED 케이블에 연결하세요. 설치에 필요한 중요한 하드웨어 정보만을 • [PWR]: 전원 스위치 케이블에 연결하세요. 포함하고 있습니다. 보다 상세한 정보 및 과정은...
Page 73 • maklumat perkakasan asas yang anda mungkin perlu [SPKR]: Sambungkan ke kabel Sistem Pembesar Suara. • semasa memasang papan induk abit anda. Untuk [SLED]: Sambungkan ke kabel Gantung LED. • pengendalian lanjutan, anda perlu rujuk ke versi [PWR]: Sambungkan ke kabel Suis Kuasa.
Page 74 เป็ น เพี ย งข้ อ มู ล พื ้ น ฐานที ่ จ ำเป็ น ใน [SPKR]:ต่ อ เข้ า กั บ สายลำโพงของระบบ • การติ ด ตั ้ ง แผงวงจรหลั ก abit ของคุ ณ เท่ า นั ้ น กรุ ณ า [SLED]:ต่ อ เข้ า กั บ สาย LED •...
Page 75 與 RAID 0、1、5 及 10） ™ • abit uGuru 技術 • JMicron JMB363 晶片組提供 2 組外部 ™ • abit Silent OTES 技術 SATA 3Gb/s 接頭，支援 RAID 0 、 1 及 JBOD • 外部 CMOS 清除開關功能 • 快速的電源與重置按鈕...
Page 76 4.19.2 快速安裝略說本「快速安裝略說」僅包含安裝 abit 主機板時所需的附加的 USB 連接埠接頭：[FP-USB1]、[FP-USB2] 基本硬體資訊。詳細的操作方式，仍請參閱其完整的除了位於 I/O 面板上的內建 USB 接頭外，您可透過帶有手冊版本。支架的延長線，連接這些各有兩個附加 USB 連接埠的接頭。硬體安裝注意事項附加的 IEEE 1394 連接埠接頭：[FP-1394-1]、[FP-1394-2] • 安裝機板或變換任何設定之前，請先關閉電源並拔除了位於 I/O 面板上的內建 IEEE 1394 接頭外，您可透掉電源插頭。過帶有支架的延長線，連接這些各有一個附加 IEEE • 從抗靜電袋中取出機板前，請先戴上靜電安全手 1394 連接埠的接頭。...
Page 77 3Gb/s 接头支持 Intel 矩阵储存科技（AHCI ™ • abit uGuru 技术与 RAID 0、1、5 及 10） ™ • abit Silent OTES 技术 • JMicron JMB363 芯片组提供 2 组外部 • 外部 CMOS 清除开关 SATA 3Gb/s 接头，支持 RAID 0、 1 及 JBOD • 快速的电源与复位按钮...
Page 78 4.20.2 快速安装略说 [PLED]：连接电源 LED 电缆。本“快速安装略说”仅包含基本的硬件信息，供您在 • 安装 abit 主板时进行参考。如需了解高级操作，仍请附加的 USB 端口接头：[FP-USB1]、[FP-USB2] 参阅其完整的手册版本。除了位于 I/O 面板上的板载 USB 连接器外，这些接头可以通过带线卡的延长电缆分别提供两个附加的 USB 端硬件设置注意事项口连接。 • 在安装主板或更改任何设置前，务必关闭电源并从附加的 IEEE 1394 端口接头：[FP-1394-1]、[FP-1394-2] 交流插座上拔掉电源线。除了位于 I/O 面板上的板载 IEEE 1394 连接器外，这些 •...
Page 79 Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into consideration of the ESCD’s legacy information. Early PCI Initialization: -Enumerate PCI bus number. -Assign memory & I/O resource -Search for a valid VGA device & VGA BIOS, and put it into C000:0 IP35 Pro...
Page 80 2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to “AUTO” 1. Initialize floppy controller 2. Set up floppy related fields in 40:hardware Detect & install all IDE devices: HDD, LS120, ZIP, CDROM … IP35 Pro...
Page 81 Update keyboard LED & typematic rate 1. Build MP table 2. Build & update ESCD 3. Set CMOS century to 20h or 19h 4. Load CMOS time into DOS timer tick 5. Build MSIRQ routing table Boot attempt (INT 19h) IP35 Pro...
Page 82 Complete power off sequence Others Either the external “EZ-CCMOS1” switch or the internal “CCMOS1” jumper is not C.C. set to its normal position. F.0. Button reset F.1. SoftMenu reset F.2. Power on sequence timeout F.3. Power off sequence timeout IP35 Pro...
Page 83 If the situation remains the same, try Step 3. Step 3. The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button battery during CMOS discharge. IP35 Pro...
Page 84 Example: Intel 650 3.4GHz (OC FSB=220MHz) • Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) • Memory size: Type in the size of your memory module. Example: 512M* 4PCS IP35 Pro...
Page 85 See the next page for a blank Technical Support Form, or visit our website to fill in the form on line (http://www.abit.com.tw/page/en/contact/technical.php). Q. Is the motherboard dead? Do I need to return it to where I bought from or go...
Page 86 Region: E-mail: First name: Last Name: Subject: Motherboard: BIOS Version: CPU: Memory brand: Memory size: Memory configuration: Graphics card: Graphics driver version: Power supply maker: Power supply wattage: Storage devices: Optical devices: Other devices: Operating system: Problem description: IP35 Pro...
Page 87 Universal ABIT (USA) Corporation 2901 Bayview Drive, Shanghai Fremont, CA 94538, U.S.A. Tel: 1-510-623-0500 Universal ABIT (Shanghai) Co. Ltd. Fax: 1-510-623-1092 FL 19 Xuhui Yuan BLOG NO.1089 Website: http://www.abit-usa.com ZhongShan s 2 RD, ShangHai 200030 The People's Republic of China Latin America: r aymond@abit-usa.com...
Page 88 P/N: 4310-0000-77 Rev. 1.00...

Abit IP35 Pro Manuel D'utilisation

Liens rapides

Manuels Connexes pour Abit IP35 Pro

Sommaire des Matières pour Abit IP35 Pro