Page 1
GeForce 7025/nForce 630a (AN-M2) GeForce 7050PV/nForce 630a (AN-M2HD) 2000MT/s HT AN-M2HD Dual Channel DDR2 800 NVIDIA PureVideo™ NVIDIA nView™ HDMI (AN-M2HD) / DVI (AN-M2) Gigabit LAN SATA 3Gb/s RAID USB 2.0 / IEEE1394 (AN-M2HD) Motherboard 7.1-Channel HD Audio AMD Socket AM2 abit SoftMenu™...
Page 2
All manuals and user guides at all-guides.com AN-M2/AN-M2HD User’s Manual English + Multilingual QIG P/N: 4310-0000-84 Rev. 3.00, April 2007 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.
Page 3
All manuals and user guides at all-guides.com Contents 1. Hardware Setup ............... 1-1 1.1 Specifications................1-1 1.1.1 AN-M2 ................1-1 1.1.2 AN-M2HD................1-2 1.2 Motherboard Layout ..............1-3 1.2.1 AN-M2 ................1-3 1.2.2 AN-M2HD................1-4 1.3 Choosing a Computer Chassis ............1-5 1.4 Installing Motherboard ..............
Page 5
All manuals and user guides at all-guides.com 1. Hardware Setup 1.1 Specifications 1.1.1 AN-M2 Expansion Slots • Supports Socket AM2 940 Processor • 1x PCI-E X16 slot with 2000MT/s system bus using Hyper • 1x PCI-E X1 slot Transport™ Technology •...
Page 6
• 4x USB 2.0 connectors • 1x RJ-45 Gigabit LAN connector • Onboard Gigabit LAN abit Engineered Audio ™ • abit Softmenu Technology • Onboard 7.1-CH HD Audio CODEC RoHS • Supports auto jack sensing and S/PDIF • 100% Lead-free process and RoHS...
Page 7
All manuals and user guides at all-guides.com 1.2 Motherboard Layout 1.2.1 AN-M2 AN-M2/AN-M2HD...
Page 8
All manuals and user guides at all-guides.com 1.2.2 AN-M2HD The motherboard and its component layouts illustrated in the following chapter ※ of this manual were mainly based on model “AN-M2HD”, unless specifically stated. AN-M2/AN-M2HD...
Page 9
Install the motherboard with screws and have them tightened. To prevent shorting the PCB circuit, ※ please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mounting-holes on the motherboard to align with. AN-M2/AN-M2HD...
Page 10
For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS setup menu right after powering on system. Set the CPU operating speed back to its default or an appropriate value. Save and exit the BIOS setup menu. AN-M2/AN-M2HD...
Page 11
Enter the BIOS setup menu. Reconfigure the setup parameters if necessary. CAUTION: Danger of explosion may arise if the battery is incorrectly renewed. ※ Renew only with the same or equivalent type recommended by the battery ※ manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions. ※ AN-M2/AN-M2HD...
Page 12
A minimum power of 300W or higher is recommended. ATX12V1: ATX 12V 4-Pin Power Connector This connector supplies power to CPU. The system will not start without connecting power to this one. AN-M2/AN-M2HD...
Page 13
• CPUFAN1: CPU Fan Power Connector • SYSFAN1: System Fan Power Connector • AUXFAN1~2: Auxiliary Fan Power Connector These fan connectors are not jumpers. DO NOT place jumper caps on these ※ connectors. AN-M2/AN-M2HD...
Page 14
CPU. The lever clicks when it’s locked into position. 3. The heatsink for CPU may have thermal interface material attached bottom. If not, applying a few squeeze of thermal paste to the CPU die will help to increase the contact. 1-10 AN-M2/AN-M2HD...
Page 15
※ A higher fan speed will be helpful for better airflow and heat-dissipation. Nevertheless, stay alert to not touch any heatsink since a high temperature generated by the working system is still possible. AN-M2/AN-M2HD 1-11...
Page 16
DIMM module. Static electricity can damage the electronic components of the computer or ※ optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly. 1-12 AN-M2/AN-M2HD...
Page 17
Make sure to configure the “Master” and “Slave” relation before connecting ※ two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. AN-M2/AN-M2HD 1-13...
Page 18
SATA device and connect the other end from the power supply. The motherboard in this photo is served for DEMO only, and may not be the ※ same type or model as the one described in this user’s manual. 1-14 AN-M2/AN-M2HD...
Page 19
I/O panel or the front-mounted IEEE1394 port of your chassis. Pin Assignment Pin Assignment TPA0 + TPA0 - Ground Ground TPB0 + TPB0 - +12V +12V Ground Make sure the connecting cable bears the same pin assignment. ※ AN-M2/AN-M2HD 1-15...
Page 20
Pin 4 “AVCC” of this header. Pin Assignment Pin Assignment (HD AUDIO) (AC’97 AUDIO) MIC2 L MIC In AGND MIC2 R MIC Power AVCC FRO-R Line Out (R) MIC2_JD F_IO_SEN FRO-L Line Out (L) LINE2_JD 1-16 AN-M2/AN-M2HD...
Page 21
The audio driver is originally configured to support HD Audio. For AC’97 audio connection, you may: Right-click the “Realtek HD Audio Manager” icon system tray. Click “Audio I/O” tab, and then click “Connector Settings”. Click “Disabled front panel jack detection”, and then click “OK” to confirm. AN-M2/AN-M2HD 1-17...
Page 22
VCC (5V) S/PDIF Out Ground 1.8.8 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot “PCIEXP1”. Install PCI Express X1 cards into slot “PCIE1”. Install PCI cards into slots “PCI1”, and/or “PCI2”. 1-18 AN-M2/AN-M2HD...
Page 23
All manuals and user guides at all-guides.com 1.9 Onboard Indicators 1.9.1 Power Source Indicators • 5VSB: This LED lights up when the power supply is connected with power source. • VCC: This LED lights up when the system power is on. AN-M2/AN-M2HD 1-19...
Page 24
All manuals and user guides at all-guides.com 1.10 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: AN-M2 AN-M2HD • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. •...
Page 25
In order to increase system stability and performance, our engineering staff is ※ constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen. AN-M2/AN-M2HD...
Page 26
This item selects the external clock frequency. Due to the specification limit of the CPU you installed, the speed you set over its standard bus speed is supported, but not guaranteed. PCIe Clock This item selects the clock frequency for PCI Express slot. AN-M2/AN-M2HD...
Page 27
This option allows you to switch between the default and user-defined voltages. Leave this setting at default unless the current voltage setting cannot be detected or is not correct. The option “User Define” enables you to select the following voltages manually. CPU Core Voltage DDR2 Voltage AN-M2/AN-M2HD...
Page 28
IDE HDD Auto-Detection Press Enter Item Help IDE Channel 1 Master Auto Access Mode Auto Capacity 0 MB Cylinder Head Precomp Landing Zone Sector :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults AN-M2/AN-M2HD...
Page 29
This item determines whether the system stops if an error is detected during system boot-up. [All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error. [No Errors]: The system-boot will not stop for any error detected. AN-M2/AN-M2HD...
Page 30
640K for systems with 640K or more memory size installed on the motherboard. Extended Memory This item displays the amount of extended memory detected during system boot-up. Total Memory This item displays the total memory available in the system. AN-M2/AN-M2HD...
Page 31
[Off]: The numeric keypad functions as arrow keys. Security Option This item determines when the system will prompt for password - every time the system boots or only when enters the BIOS setup. [Setup]: The password is required only when accessing the BIOS Setup. AN-M2/AN-M2HD...
Page 32
This item allows the BIOS to support some old or special IDE devices by prolonging this delay time. A larger value will give more delay time to the device for which to initialize and to prepare for activation. Full Screen LOGO Show This item determines to show the full screen logo when booting. AN-M2/AN-M2HD...
Page 33
For example: In a 256M selection with 256M total system memory size configuration, the BIOS utility will force it down to 128M automatically. In the applications that require higher frame buffer size, such as 3-D game, HDMI, or Blu-ray DVD playing, please select the option [256MB] for higher video performance. AN-M2/AN-M2HD...
Page 34
Phoenix – AwardBIOS CMOS Setup Utility OnChip IDE/SATA Device ► IDE/SATA Function Setup Press Enter Item Help ► RAID Configuration Press Enter :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults 2-10 AN-M2/AN-M2HD...
Page 35
Item Help x - SATA1 RAID Disabled x - SATA2 RAID Disabled x - SATA3 RAID Disabled x - SATA4 RAID Disabled :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults AN-M2/AN-M2HD 2-11...
Page 36
This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Onboard FDD Controller This option enables or disables the floppy disk controller. (For AN-M2HD only) Onboard 1394 Controller This option enables or disables the IEEE 1394 controller. 2-12 AN-M2/AN-M2HD...
Page 37
Soft-Off condition. The PCI card must support the wake up function. Wake Up by OnChip LAN When set to [Enabled], access through the onchip LAN port can remotely wake up the system that was in Soft-Off condition. AN-M2/AN-M2HD 2-13...
Page 38
AC power failure occurs, the system will power-on when power returns. HPET Support This item selects to support the “High Precision Event Timer” (HPET), a new timer hardware for use by the system software when generating interrupts for thread schedulers, kernels, and multimedia timer servers. 2-14 AN-M2/AN-M2HD...
Page 39
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not. [Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA. [Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA. Maximum Payload Size This item sets the maximum TLP payload size for the PCI Express devices. AN-M2/AN-M2HD 2-15...
Page 40
CPU FANEQ Control This item allows you to control the CPU fan speed. When set to [Enabled], the following items become selectable. CPU FanEQ Target Temp. This item sets the temperature mark for the “CPU FanEQ” function to take effect. 2-16 AN-M2/AN-M2HD...
Page 41
“SYS FanEQ Target Temp.” plus the value of item “SYS FanEQ Temp. Tolerance”, the speed ratio for the 3-pin fan assembly connected at “SYSFAN1” fan power connector will first run at the speed ratio set by the item “SYS FanEQ Start Control”, and then up to 100%. AN-M2/AN-M2HD 2-17...
Page 42
This option protects the BIOS configuration or restricts access to the computer itself. 2.12 Save & Exit Setup This option saves your selections and exits the BIOS setup menu. 2.13 Exit Without Saving This option exits the BIOS setup menu without saving any changes. 2-18 AN-M2/AN-M2HD...
Page 43
• [Utility]: Click to enter the utilities installation menu. • [abit Utility]: Click to enter the installation menu of utilities exclusively developed by abit. • Browse CD]: Click to browse the contents of this “Driver-&-Utility CD”. • Close]: Click to exit this installation menu.
Page 44
Click the [Realtek HD Audio Driver] item. The installation screen appears. Follow the prompts on the screen to complete installation. After restarting the system, right-click the Sound Manager icon located at the desktop shortcut. Click item “Sound Manager”. The Realtek HD Audio Manager appears. AN-M2/AN-M2HD...
Page 45
All manuals and user guides at all-guides.com Click the [Audio I/O] tab. Click the pull down menu to select the channel configuration. Click [OK] button to apply the Audio I/O settings and exit. AN-M2/AN-M2HD...
Page 46
“Automatic Mode” for Cool ‘n’ Quiet to be enabled. 3.5 USB 2.0 Driver There is no need to install this driver for Windows 2000 with Service Pack 4, ※ Windows XP with Service Pack 1, or their later version. AN-M2/AN-M2HD...
Page 47
The abitEQ is a self-diagnostic system that protects PC Hardware by monitoring critical items of Power Supply Voltage, CPU & System Fans Speed, and CPU & System Temperature. To install this utility: Click on the [abit Utility] tab in the installation menu screen. Click the [abitEQ] item. The following screen appears.
Page 48
3.7 FlashMenu (BIOS Update Utility) The FlashMenu is a utility to flash the BIOS in a more easily and quickly way. To install this utility: Click on the [abit Utility] tab in the installation menu screen. Click the [FlashMenu] item. The following screen appears.
Page 49
Save this selection and exit BIOS setup menu by accessing the BIOS menu “Save & Exit Setup”. Restart the system. The system will now boot from CD, and enter the ABIT Boot Manager, the following options appear (0) Boot From First HDD...
Page 50
All manuals and user guides at all-guides.com AN-M2/AN-M2HD...
Page 51
• [SLED]: Connecte au câble de la DEL de veille. l’installation de votre carte mère abit. Pour des opérations plus • [PWR]: Connecte au câble de l’interrupteur de l’alimentation avancées, vous devez vous reporter à la version complète.
Page 52
Diese “Kurze Installationsanleitung” enthält nur die Anschlüsse auf der Vorderseite: [FPIO1] grundlegenden Hardwareinformationen, die Sie zur [HLED]: Kabelanschluss für Festplattenzugriffsanzeige. • Installation Ihres abit-Motherboards benötigen. Details [RST]: Kabelanschluss für Rücksetzschalter. • finden Sie im ausführlichen Handbuch. [SPKR]: Kabelanschluss für Kabelanschluss für •...
Page 53
• [PLED]: collega al cavo LED alimentazione. le informazioni di base sull’hardware necessarie all’installazione della scheda madre abit. Fare riferimento Collettore porta USB aggiuntiva: [FP-USB1], [FP-USB2] alla versione completa della guida per eseguire le Collettore porta IEEE1394 aggiuntiva: [FP-1394-1], [FP-1394-2] operazioni avanzate.
Page 54
[PWR]: Conecte el cable del interruptor de encendido. • durante la instalación de la placa base abit. Para conocer el [PLED]: Conecte el cable del LED de encendido. • funcionamiento avanzado, es necesario consultar la Terminal de puerto USB adicional: [FP-USB1], [FP-USB2] versión completa.
Page 55
à • [PWR]: Faz a ligação ao cabo do botão de alimentação. instalação da sua placa principal abit. Para mais • [PLED]: Faz a ligação ao cabo do LED do botão de alimentação.
Page 56
основная информация о техническом обеспечении, которая • [PLED]: Соединяется с кабелем индикатора питания. вам может понадобиться при установке материнской платы abit. Описание дополнительных операций вы найдете в Дополнительная насадка порта USB: [FP-USB1], [FP-USB2] полной версии руководства. Дополнительная насадка порта IEEE1394: [FP-1394-1], [FP-1394-2] Предостережения...
Page 57
All manuals and user guides at all-guides.com 4.7 Eesti//Kiirpaigaldusjuhend Käesolev “Kiirpaigaldusjuhend” sisaldab ainult [SLED]: Ühendage peatusindikaatori (Suspend LED) • abit-emaplaadi paigaldamiseks vajalikku riistvaraalast kaabliga. põhiteavet. Edasijõudnud kasutamiseks tuleb teil ikkagi [PWR]: Ühendage toitelüliti kaabliga. • pöörduda täisversiooni poole. [PLED]: Ühendage toiteindikaatori (Power LED) kaabliga.
Page 58
All manuals and user guides at all-guides.com 4.8 Latviski//Ātrās instalēšanas instrukcija Šī “Ātrās instalēšanas instrukcija” ietver tikai pamata [RST]: Pievieno atiestates slēdža kabeli. • norādes iekārtai, kas nepieciešamas, instalējot abit [SPKR]: Pievieno sistēmas skaļruņa kabeli. • mātesplati. Pilnīgākai darbībai nepieciešams iegūt [SLED]: Pievieno LED pārtraukšanas kabeli.
Page 59
[SLED]: Sujunkite su darbo pristabdymo indikatoriaus • informacija apie techninę įrangą, kurios jums gali prireikti kabeliu. instaliuojant pagrindinę plokštę abit. Papildomų operacijų [PWR]: Sujunkite su maitinimo tinklo jungiklio kabeliu. • aprašymą rasite pilnoje vadovo versijoje. [PLED]: Sujunkite su maitinimo indikatoriaus kabeliu.
Page 60
[SLED]: Podłączenie kabla diody LED wstrzymania pracy. • podstawowe informacje dotyczące sprzętu, wymagane [PWR]: Podłączenie kabla przełącznika zasilania. • podczas instalacji płyty głównej abit. Przy [PLED]: Podłączenie kabla diody LED zasilania. • zaawansowanych operacjach, niezbędne będzie skorzystanie z kompletnej wersji instrukcji.
Page 61
4.11 Magyar//Gyorstelepítési útmutató Ez a “Gyorstelepítési útmutató” csak azt az alapvető [PWR]: Csatlakoztassa a tápkapcsoló kábelhez. • hardver információt tartalmazza, amely az abit alaplap [PLED]: Csatlakoztasson a táp LED kábelhez • telepítéséhez szükséges. Az előrehaladott üzemeltetéshez, Kiegészítő USB port fejrész: [FP-USB1], [FP-USB2] továbbra is a teljes útmutatót kell használnia.
Page 62
All manuals and user guides at all-guides.com 4.12 Türkçe//Hızlı Kurulum Kılavuzu Bu “Hızlı Kurulum Kılavuzu”, abit anakartınızı takmanızda Ön Panel Konnektörleri: [FPIO1] gerekebilecek sadece temel donanım bilgisini içermektedir. [HLED]: Sabit Disk Sürücü LED kablosuna bağlayın. • İleri işlemler için daha geniş olan tam versiyonuna [RST]: Sıfırlama Anahtarı...
Page 63
All manuals and user guides at all-guides.com دﻟﻴﻞ اﻟﺘﺮآﻴﺐ اﻟﺴﺮﻳﻊ اﻟﻠﻐﺔ اﻟﻌﺮﺑﻴﺔ 4.13 AN-M2/AN-M2HD 4-13...
Page 64
All manuals and user guides at all-guides.com راهﻨﻤﺎﯼ ﻧﺼﺐ ﺳﺮﻳﻊ ﻓﺎرﺳﯽ 4.14 4-14 AN-M2/AN-M2HD...
Page 65
All manuals and user guides at all-guides.com 4.15 日本語//クイックインストールガイド • この「クイックインストールガイド」には、abit マ [SPKR]: システムスピーカーケーブルに接続 • [SLED]: サスペンド LED ケーブルに接続 ザーボードを取り付けるときに必要となるハードウ • [PWR]: 電源スイッチケーブルに接続 ェアの基本情報のみが含まれています。詳細な操作 • [PLED]: 電源 LED ケーブルに接続 については、その完全版を参照してください。 ハードウェアのセットアップに関する注意事項 追加 USB ポートヘッダ: [FP-USB1]、[FP-USB2] • ボードを取り付けたり設定を変更するときは、 事前に 追加 IEEE1394 ポートヘッダ: [FP-1394-1]、[FP-1394-2] 電源装置をオフにし、AC コンセントからプラグを必...
Page 66
All manuals and user guides at all-guides.com 4.16 한국어//빠른 설치 가이드 본 “빠른 설치 가이드”는 빅빔 abit 메인보드 • [SPKR]: 시스템 스피커 케이블에 연결하세요. • [SLED]: 유휴(Suspend) LED 케이블에 연결하세요. 설치에 필요한 중요한 하드웨어 정보만을 • [PWR]: 전원 스위치 케이블에 연결하세요.
Page 67
• maklumat perkakasan asas yang anda mungkin perlu [SPKR]: Sambungkan ke kabel Sistem Pembesar Suara. • semasa memasang papan induk abit anda. Untuk [SLED]: Sambungkan ke kabel Gantung LED. • pengendalian lanjutan, anda perlu rujuk ke versi [PWR]: Sambungkan ke kabel Suis Kuasa.
Page 74
All manuals and user guides at all-guides.com 4.20.3 快速安装略说 [PLED]:连接电源 LED 电缆。 本“快速安装略说”仅包含基本的硬件信息,供您在 • 安装 abit 主板时进行参考。如需了解高级操作,仍请 附加的 USB 端口接头:[FP-USB1]、[FP-USB2] 参阅其完整的手册版本。 除了位于 I/O 面板上的板载 USB 连接器外 , 这些接头可 以通过带线卡的延长电缆分别提供两个附加的 USB 端 硬件设置注意事项 口连接。 • 在安装主板或更改任何设置前,务必关闭电源并从 附加的 IEEE1394 端口接头:[FP-1394-1]、[FP-1394-2] 交流插座上拔掉电源线。 除了位于 I/O 面板上的板载 IEEE1394 连接器外,这些...
Page 75
If the situation remains the same, try Step 3. Step 3. The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button battery during CMOS discharge. AN-M2/AN-M2HD...
Page 76
Example: Intel 650 3.4GHz (OC FSB=220MHz) • Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) • Memory size: Type in the size of your memory module. Example: 512M* 4PCS AN-M2/AN-M2HD...
Page 77
See the next page for a blank Technical Support Form, or visit our website to fill in the form on line (http://www.abit.com.tw/page/en/contact/technical.php). Q. Is the motherboard dead? Do I need to return it to where I bought from or go...
Page 78
5.1.2 Technical Support Form Region: E-mail: First name: Last Name: Subject: Motherboard: BIOS Version: CPU: Memory brand: Memory size: Memory configuration: Graphics card: Graphics driver version: Power supply maker: Power supply wattage: Storage devices: Optical devices: Other devices: Operating system: Problem description: AN-M2/AN-M2HD...
Page 79
Universal ABIT (USA) Corporation 2901 Bayview Drive, Shanghai Fremont, CA 94538, U.S.A. Tel: 1-510-623-0500 Universal ABIT (Shanghai) Co. Ltd. Fax: 1-510-623-1092 FL 19 Xuhui Yuan BLOG NO.1089 Website: http://www.abit-usa.com ZhongShan s 2 RD, ShangHai 200030 The People's Republic of China Latin America: r aymond@abit-usa.com...
Page 80
All manuals and user guides at all-guides.com http://www.abit.com.tw P/N: 4310-0000-84 Rev. 3.00...