Publicité
Les langues disponibles
Les langues disponibles
6. Fuse
7. Heating switch
8. Power switch
9. Power socket
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
Attention: DO NOT touch directly the pan and heating head.
Wear heat resistant gloves (not supplied) if necessary.
• Turn on the power switch and let the machine run for 1-2
minutes. If the machine needs adjusted, the machine will
shake. Please make sure the machine is running smoothly
before continuing.
• Turn on the heating switch and let the machine warm-up for
about 4-5 minutes.
• Pour one spoonful of the granulated sugar into the center of
the running head.
• The candy floss will form after roughly 30 seconds. Use a can-
dy stick or other related object for the candy floss to stick to.
Revolve the stick in a circular motion following the pan.
• To continue to make candy floss, repeat the above procedures.
• Once all candy floss has been gathered, put little water into
the heating head and repeat 4-5 times for cleaning inside.
• Turn off and unplug the machine for cleaning outside. (see
----->Cleaning and Maintenance)
Note:
• Allow the motor to rest for 20 minutes after working contin-
uously for an hour.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems
Possible cause
Voltage meter
Power plug and
is abnormal.
the outlet are not
Heating head and
connected firmly.
indicators do not
functional.
Fuse is blew out.
Electrical
components are
damaged.
Voltage meter is
Heating element
normal. Heating
becomes
head does not
functional but indi-
cators light on.
Possible solution
Check again the
connections and
make sure they are
firmly connected.
Replace the fuse.
Contact your
supplier.
Contact the
defective.
supplier.
7
GB
Publicité
