Toshiba SL-3329 Mode D'emploi page 8

4. Set the DUBBING SPEED/FM MODE/BEAT selector @ to
"NORMAL" or "HIGH" position.
5. Press the deck B PAUSE button (1 6) first, and next the REC
button @ .
6. Press the deck A PLAY button @ | Dubbing from deck A to
deck B starts.
7. Press the deck A and B STOP/EJECT buttons @ , @) when
you want to stop dubbing.
8. Turn off the power by pressing the POWER switch @ again.
= To record a compact disc
1, Press the POWER switch @ to turn on the power.
2, Follow steps of ''To listen to a compact disc/Manual Play".
3. Press the deck B STOP/EJECT button @_, insert a cassette
tape and close the door.
4. Press the deck B PAUSE button @® first, and next the REC
button @ .
5. Begin compact disc play.
6. To begin actual recording, release the deck B PAUSE button
7. To stop recording, press the deck B STOP/EJECT button ® .
8. Turn off the power by pressing the POWER switch (3) again.
Precaution
@ Use normal type cassette tapes with this deck. If other types of
cassettes are used, sound quality may deteriorate and the pre-
vious program may not be completely erased when making a
new recording.
@ This unit employs a one-touch recording system. Be sure you
press only the deck B REC button @ to start recording.
@ if a whistling sound is heard during AM broadcast recording,
set the DUBBING SPEED/FM MODE/BEAT selector @ to the
position in which the whistling sound is less prominent.
® Minor differences in actual tape length exist even between
tapes of the same stated length made by the same manufacturer.
Therefore, even when playback or recording to both decks is
started simultaneously, the cassettes may not end precisely at
the same time.
@ To keep the cassette deck sounding like new, clean the record/
playback heads regularly using a cotton swab moistened with
alcohol. Wait until the head is dry before playing tapes again.
@ C-120 cassettes are not recommended since the tape tends to
tangle and jam the transport mechanism.
@ The turning speed is slightly between the deck A and B for the
reason of functions.
® Do not switch the DUBBING SPEED/FM MODE/BEAT selector
during dubbing. Switch may alter sound quality and cause
sound interruption.
Specifications
= General
Power supply:
Power consumption:
Dimensions:
Weight:
= Turntable
Drive system:
Motor:
Turntable platter:
Speed:
Wow and flutter:
Signal to noise ratio:
Cartridge:
Stylus:
= Tuner
Frequency range:
Sensivitity:
Signal to noise ratio:
(IHF A Network)
Stereo separation:
= Amplifier
Rated output power:
Music power output:
Total harmonic distor-
tion:
Output terminals:
Graphic equalizer:
= Cassette Deck
Track system:
Tape speed:
Recording system:
Heads:
Wow and flutter:
Frequency response:
Signal to noise ratio:
Motor:
AC 220 Vv, 50 Hz
35 watts
360 (W) X 417 (H) X 319 (D) mm
7.3 kg
Belt drive
DC motor, Electric governor
28cm
Two speed 33-1/3 and 45 rpm
Less than 0.3% (WRMS)
More than 45dB (DIN B)
Ceramic Type
N-73C
FM: 87.5 ~108.0 MHz
MW: 526.5 ~ 1606.5 kHz
LW: 150 ~260 kHz
FM: 2.0 uv
MW: 500uV/m
LW: 900"UV/m
FM mono: 62dB
FM stereo: 52dB
30dB (1kHz)
5W, (per channel 10% THD, at 4 ohms
1 kHz)
TOW, (per channel 10% THD, at 4 ohms
1 kHz)
0.2% at half rated output power,
1 kHz
Headphones, speakers
Center frequencies:
100 Hz, 1 kHz, 10 kHz
Adjustment range: +10dB
4 track, 2 channel (stereo)
4.75 cm/sec.
AC bias
Deck A: Pb: 1
Deck B: Rec/Pb: 1 Erase: 1
0.15% (WRMS)
40Hz to 14kHz (Normal tape)
50dB (Normal tape)
Electrically controlled DC type: 1
= Compact Disc Player
Type:
Channels:
Pickup:
Random access:
| Speaker System
Speaker:
Impedance:
Input power:
Dimensions:
Weight:
Compact Disc player with optical pickup
2 channel (Stereo)
Semiconductor laser type
By track number
12 cm full-range P
4 ohms
Rated: 5 watts
Maximum: 10 watts
230{W) x 365(H) x 140(D) mm
1.8 kg (each)
@ Design and specifications are subject to change without notice.