Eurocave Premiere Serie Mode D'emploi page 12

4/ INSTALLING YOUR WINE CABINET
10
Put the door back on its pin.
13
12
11
11
Put in place the upper hinge.
12
Screw the hinge so that the door is completely parallel to the cabinet.
Check that the door seal adheres well to the cabinet (by closing the door),
to ensure that it is completely air-tight.
13
Put in place the caps.
5/ LAYOUT – STORAGE
Your EuroCave cabinet was designed to be adaptable. Its storage equipment adapts to your requirements and can be added to over time.
Different types of storage
Universal storage shelf
Ref.: AXUH
Capacity: 77 bottles
Max weight: 100 kg
Champagne sliding
shelf
Ref. : ACHH
Capacity: 10 bottles
Articulated
presentation kit for
ACMS shelves
Ref.: AOPRESAR
Capacity: 32 bottles
10
GB
14
As the door has been reversed, gently remove the lighting adhesive
mounting support, now located at the bottom of the door. (only for
glass door)
You will then find a second adhesive support in your accessories bag,
to be positioned inside your door, at the top and the centre :
- glass door : under the seal
- solid door : see diagram below
To ensure that the lighting is correctly positioned, gently close the
door.
A
A
Bordeaux Universal sliding shelf
storage shelf fitted with
Ref.: AXBH "Main du sommelier"
supports
Ref.: ACMS
Capacity: 78 bottles Capacity: 12 bottles
Max weight: 100 kg
Serving sliding shelf Display shelf
Ref.: ACVH Ref.: ACPH
Capacity: 20 bottles Capacity: 22 bottles
5/ LAYOUT – STORAGE
The layout of your cabinet can be modified according to your requirements. Refer to pages 111-112 to see storage simulations.
Layout advice
Your EuroCave wine cabinet has been designed to safely hold a maximum
number of bottles. We recommend that you observe the following advice
to optimize loading.
•
Distribute your bottles as uniformly as possible over the various cabinet
shelves, in order to spread the weight. Also ensure that none of the bottles
is touching the rear wall of the cabinet.
•
Spread the load over the entire cabinet rather than placing bottles all at
the top or all at the bottom.
•
Observe the loading instructions for the specific storage layout of your
cabinet and never stack bottles on a sliding shelf.
•
If you have sliding shelves, it is preferable to position them in the upper
section of your cabinet to facilitate daily access.
Note: adjusting an ACMS/ACHH sliding shelf
When you purchase your cabinet, the sliding shelves are already adjusted
to ideally suit the internal dimensions of your appliance. If you purchase
a new sliding shelf, you may have to carry out this adjustment. To do so,
unscrew the screws 1 of the first right or left runner 2 (2 screws) then
position the runner at the desired width and tighten the screws. Repeat
this process for the second runner (if necessary).
Adding or changing the position of a sliding shelf
If the sliding shelf is already in place in your cabinet:
•
Completely unload the sliding shelf.
•
Then remove the sliding shelf by sliding it towards you whilst lifting the front section.
•
Remove the slide guides from the walls, marking off the right guide and the left guide.
•
Refit the slide guides (see diagram below).
A. Putting in place the back section of the guide
Wall
Guide
Wall
Guide
C. Then place the sliding shelf
Sliding shelf
Guide
•
In the same way, place one or two bottles of each of your
different wines on the sliding shelves and keep spare bottles on
the storage shelves. You then simply replace bottles when they
are consumed.
•
When using your wine cabinet, never pull out more than one
sliding shelf at a time.
NB: Never modify the position of the stiffener in your V-Pure-L
cabinet (see description page 6) without first consulting your
retailer and never handle this part when the cabinet is loaded.
2
1 2
B. Putting in place the front section of the guide
Guide
Wall
Guide
Wall
11
GB