Eurocave Premiere Serie Mode D'emploi page 11

4/ INSTALLING YOUR WINE CABINET
Precautions
•
Do not place your cabinet in an area liable to flood.
•
Do not place your cabinet close to a source of heat or expose it to
direct sunlight
•
Prevent water from splashing on any parts of the rear of the machine.
•
Arrange the power lead so that it is accessible and does not come into
contact with any of the appliance's components.
•
Tilt the cabinet slightly backwards in order to adjust the front feet (by
screwing or unscrewing them) so that you can level your cabinet (spirit
level recommended).
•
Install the stop (which is located in the accessories bag) at the back of
the cabinet (see diagram).
•
This allows a space of 7 cm
to be maintained between
the wall and the rear of the
cabinet. This spa
ce allows your cabinet's
power consumption to be
optimised.
•
Place the 2 caps in the 2
holes at the top of the
cabinet.
•
Do not push the caps all
the way in, in order to
allow the rear stop to be
installed.
•
Slide the rear stop between
the caps and the wall of the
cabinet, then push the 2 caps all the way in.
Installation
Place your cabinet in the desired location.
It must:
•
be open to the outside and well ventilated (not in an enclosed
cupboard, for example),
•
not be too damp (utility room, laundry room, bathroom...),
•
have a flat, stable floor,
•
be supplied with power (standard outlet, 16 A, earthed with 30mA*
circuit breaker). (* not applicable to some countries).
•
Place your cabinet in the desired location.
•
Fit the charcoal filter (located in the "accessories" bag) by inserting it
into the breather hole located on the top left-hand side of the inside of
your cabinet (see diagram below).
8
GB
•
Wait 48hrs before plugging in your cabinet.
Bottles must be arranged so that they do not come into contact
with the back wall. If this happens, the condensation created on
the wall may trickle onto the shelves and damage the bottle
labels. In addition, contact with the cold wall may create a frost point,
which is harmful to your wine.
Door security
In order to make your cabinet secure, all doors have a lock. You will find
the key for this type of lock (figure 2) in your accessories bag.
1 2
Installing two cabinets side by side
N.B.: If you are placing two cabinets side by side, ensure that you leave a
gap of one to two cm between each cabinet.
Detachable lighting with LED
This accessory comprises:
- an adhesive support fixed to the inside of your door.
- an adhesive support in your accessories bag, in case you reverse the
door.
- a tube made up of 4 LED in your accessories bag (diagram 1).
Before the first use, remember to remove the security strip
under the battery located next to the ON/OFF button.
Tube is secured in place by simply inserting it into the adhesive
support (1).
Changing the batteries: unscrew the cap on the side opposite the
ON/OFF button (2) then remove the inner tube (3).
1
3
ON/OFF button
* Ref. AAA LR03
4/ INSTALLING YOUR WINE CABINET
I. Door reversibility
x3 x3 x3
A B C D
This allows you to change the direction in which the door opens. Follow
the instructions below (example for changing a right-hand door into a left-
hand door):
4
1
Carefully remove the caps using a thin blade.
2
Unscrew the three screws using a "T25" Torx wrench.
3
Remove the upper hinge.
4
Remove the cabinet door by opening it slightly, then lifting it upwards.
2
5
Unscrew the door pin.
6
Carefully remove the cap using a thin blade and assemble the pin in its
place. Reposition the cap on the opposite side
A
x4
Upper hinge
B
Caps
C
Caps
D
E F G H J
Torx screw
E
Hex screw
x2
F
Door catch
1
7
2
7
Unscrew the two screws and the door catch.
Unscrew the two screws on the opposite side and remove the two
washers.
3
8
Mount the door catch on the desired opening side, using screws.
Replace the washers, then the screws, on the side opposite the door catch.
9
Turn the door through 180°.
Warning: the door is very heavy.
precautions to ensure that you do not injure yourself or drop it.
G
Lower hinge
H
Door pin
J
Door pin cap
8
Take any necessary
9
GB