Table des Matières
Publicité
T EC HN IC A L I N F ORMAT IO N
Water pressure
Recommended
Maximum
Hot water temp.
Recommended
Maximum
Max. flow rate
0.25 gallons (0.95 liter) per cycle**
Hole size in mounting surface
Max. depth of mounting surface
I NSTA LL AT I O N CO N SID E R ATI ONS
⁄ For best results, Hansgrohe recommends that this unit
be installed by a licensed, professional plumber.
⁄ Please read over these instructions thoroughly
before beginning installation. Make sure that you
have all tools and supplies needed to complete the
installation.
⁄ Keep this booklet and the receipt (or other proof
of date and place of purchase) for this product in
a safe place. The receipt is required should it be
necessary to request warranty parts.
⁄ Flush the hot and cold supplies thoroughly before
installing the faucet. Damage to the faucet caused
by debris is not covered under the warranty.
⁄ The hot and cold supplies should be of equal
pressure.
⁄ The faucet should not be used with a continuous flow
water heater.
⁄ Do not install the faucet on a sink with a raised edge.
⁄ Strong light sources should not shine directly on the
sensor window of the faucet.
⁄ The faucet should only be used with the battery pack
supplied by Hansgrohe. Do not attempt to use any
other battery pack.
⁄ The faucet incorporates automatic range adjustment
-- the sensor automatically adjusts itself to local condi-
tions (lavatory, brightness, etc.)
2
15 - 75 PSI (0.1 - 0.5 MPa)
145 PSI (1 MPa)
120°-140° F (48° - 60° C)*
158°F (70° C)*
1.5 GPM (5.7 L/min)
1⅜" (35 mm)
1⅝" (40 mm)
E N G L I S H
Battery
Automatic shutoff
*
Please know and follow all applicable local plumbing
codes when setting the temperature on the water heater.
** 10 second maximum cycle time
*** This is the maximum amount of time the faucet will run
while a hand is within range of the sensor.
⁄ The distance between the switch on/off point to the
faucet is approx. 6¼" - 8" under normal conditions.
The detection area may be less for dark, non-reflec-
tive objects, or greater for bright, highly reflective
objects.
If t he si nk is ve r y sm a ll or highl y re f l ec -
tive , fo l l ow t h e ra ng e re d uc t i on ins t r uc-
tio ns. Wh en t he fa uc et i s in redu c ed
rang e m o de, t he LED i n t he se nso r
w indow wi ll f l a sh w h il e t he fau c et i s not
in u se.
⁄ Drops of water or condensation on the sensor win-
dow may cause the faucet to run.
The s p ra y p at t er n wi l l b e un at t ract i ve
imm edi a tel y a f t er i ns ta l la t io n or se r v i ce,
due to ai r in t h e fa uc et . Af t er t he fau c et
is u sed 10 - 15 ti m es, t h e s p ra y pa t t e r n
w ill cle a r.
⁄ At the start of operation, or after maintenance, func-
tion of the faucet may be delayed due to reflections
during adjustment of the operating distance. The
faucet will automatically calibrate itself. The self-
calibration will start after 10-15 minutes.
Hansgrohe recommends not to use as drinking wa-
ter the first half liter (approximately 1 pint) flowing
from the faucet in the morning, or after prolonged
non-use.
CR-P2 / 6 V Lithium
after 10 seconds***
Publicité
Table des Matières
