Publicité
Liens rapides
Publicité
Manuels Connexes pour Bertazzoni MAS486BTFEPXT
Sommaire des Matières pour Bertazzoni MAS486BTFEPXT
- Page 1 BERTAZZONI INSTALLATION MANUAL FREESTANDING DUAL FUEL RANGES 3100519 WWW.BERTAZZONI.COM...
- Page 2 Installing the legs _____________________________________________________________ Installing the worktop frontguard ________________________________________________ Installing the island trim _______________________________________________________ Installing backguard (optional) __________________________________________________ INSTALLING THE ANTI-TIP DEVICES ______________________________________________ Anti-tip brackets ______________________________________________________________ Anti-tilt chain ________________________________________________________________ GAS CONVERSION _____________________________________________________________ INSTALLATION CHECKLIST ______________________________________________________ FINAL PREPARATION ___________________________________________________________ BERTAZZONI SERVICE _________________________________________________________...
- Page 3 / Models Models Models MAST305DFMBIE PROF304DFSART MAST305DFMNEE PROF304DFSBIT MAST305DFMXE PROF304DFSGIT MAST365DFMBIE PROF304DFSNET MAST365DFMNEE PROF304DFSROT MAST365DFMXE PROF304DFSXT MAST366DFSXT PROF366DFSART MAST486GDFSXT PROF366DFSBIT MAST486GDFMXE PROF366DFSGIT PROF366DFSNET HERT366DFSX PROF366DFSROT HERT366DFSAV PROF366DFSXT HERT366DFSNE PROF486GDFSART HERT486GDFSX PROF486GDFSBIT HERT486GDFSAV PROF486GDFSGIT HERT486GDFSNE PROF486GDFSNET PROF486GDFSROT PROF486GDFSXT...
- Page 4 / Warnings WARNINGS To ensure proper and safe operation, the applian- WARNING! ce must be properly installed and grounded by a If the information in these instructions is not fol- qualifi ed technician. DO NOT attempt to adjust, lowed exactly, a fi re or explosion may result cau- repair, service, or replace any part of your ap- sing property damage, personal injury or death.
- Page 5 / Warnings/ Data rating label Engage the range to the anti-tip device by anti-tip DATA RATING LABEL brackets or anti-tip chain (see installing the an- ti-tip device chapter). Ensure the anti-tip device is re-engaged when the range is moved. The data rating label shows the model and serial number of the range.
- Page 6 / Before installation BEFORE INSTALLATION • This appliance shall only be installed by an au- A manual valve shall be installed in an accessible thorized professional. location in the gas line external to the appliance • This appliance shall be installed in accordance for the purpose of turning on or shutting off...
- Page 7 For best removal of smoke and odors, the been designed to work in conjunction with the lower edge of the hood should be installed Bertazzoni range and have the same fi nish for a between 25 1/2” (65 cm) and 31 1/2” (80 cm) perfect look.
- Page 8 / Specifi cations Pressure Pressure Max Rate Max Rate Min Rate Min Rate By-pass By-pass Burner Burner Injector Injector [iwc] [Btu/hr] [Btu/hr] diam.[mm] diam.[mm] Type 4’’ 3,500 1,025 Regulated Auxiliary 0.90 10’’ 3,300 0.29 0.54 LP (Propane) 4’’ 5,900 1,728 1,500 Regulated Semi-rapid...
- Page 9 / Clearence dimensions CLEARENCES DIMENSIONS Installation adjacent to kitchen cabinets Metal hood This range may be installed directly adjacent to 30’’ (76,2 cm) existing countertop high cabinets (36” or 91.5 cm 25 1/2’’(65 cm) and 31 1/2’’ (80 cm) from the fl oor). For the best look, the worktop should be level with 13’’...
- Page 10 / Installation requirements / Electrical connection INSTALLATION REQUIREMENTS ELECTRICAL CONNECTION Warning! ELECTRICAL ELECTRICAL SHOCK HAZARD A properly-grounded horizontally- mounted electri- Disconnect electrical power at the circuit bre- cal receptacle should be installed no higher than aker box or fuse box before installing the ap- 3”...
- Page 11 / Installation requirements / Electrical connection The appliance is equipped at the factory with an electric supply cord set 4 wires type with ring terminals (L1, L2, N, Ground) suitable for range FOUR-WIRE CONN.RECEPTACLE NEMA 14-50R use UL/CSA listed type SRDT/DRT 2x6AWG (L1, L2)+2x8AWG (N, G) rated 300V, 40 or 50A with fused plug type NEMA 14-50P;...
- Page 12 / Wiring diagram WIRING DIAGRAM The electric wiring diagrams and schematics are attached behind the range, and should not be removed except by a service technician, then replaced after service. LEGENDA Simb. Description Ignition Micro switches Oven Function Selector Commutatore.9+0 COLOURS Cooling fan air sensor switch Oven lamp...
- Page 13 / Wiring diagram 30 /36 /48 DFS...
- Page 14 / Gas connection GAS CONNECTION Warning! FLEXIBLE CONNECTIONS DO NOT USE AN OPEN FLAME WHEN In case of installation with fl exible couplings and/ CHECKING FOR LEAKS! or quick-disconnect fi ttings, the installer must use a heavy-duty, AGA design-certifi ed commercial fl...
- Page 15 / Gas connection PRESSURE REGULATOR Since service pressure may fl uctuate with local demand, every gas cooking appliance must be equipped with a pressure regulator on the inco- ming service line for safe and effi cient operation. The pressure regulator shipped with the applian- ce has two female threads ½”...
- Page 16 / Installation INSTALLATION APPLIANCE INSTALLATION REMOVING THE OVEN DOOR Unpacking the range Prepare the door for removal. Flip up the locking • clamps on each door hinge. Slowly shut the door Remove all packing materials from the ship- until the protruding clamps stop the movement. ping pallet but leave the adhesive-backed foam layer over brushed-metal surfaces to protect it Pull oven door upwards and remove.
- Page 17 / Installation INSTALLING THE LEGS INSTALLING THE WORKTOP FRONTGUARD Bertazzoni ranges must be used only with the legs properly installed. To increase the clearance between the front edge Four height-adjustable legs are supplied with the of the worktop and the burners, it is possible to range in the polysterene container situated over install a front guard for the worktop.
- Page 18 / Installation INSTALLING THE ISLAND TRIM INSTALLING BACKGUARD (OPTIONAL) The island trim must be installed prior to operation The backguard must be installed prior to opera- of the appliance for appropriate ventilation of the tion of the appliance for appropriate ventilation of oven compartment.
- Page 19 / Installing the anti/tip devices INSTALLING THE ANTI/TIP DEVICES ANTI-TIP BRACKETS ANTI/TILT CHAIN The anti-tip bracket shipped with the range must The anti-tilt chain shall be installed on right or left be properly secured to the rear wall as shown in side alternatively according below instructions.
- Page 20 Replace nozzles using the conversion set sup- Save the nozzles removed from the range for fu- plied with the range or by a Bertazzoni authori- ture use. zed parts warehouse. Each nozzle has a number indicating its fl ow diameter printed on the body.
- Page 21 / Gas conversion Step 4: minimum fl ame adjustment WARNING! These adjustments should be made only for use of the appliance with natural gas. For use with li- quid propane gas, the choke screw must be fully turned in a clockwise direction. SURFACE BURNERS Light one burner at a time and set the knob to the MINIMUM position (small fl...
- Page 22 / Installation checklist / fi nal preparation INSTALLATION CHECKLIST FINAL PREPARATION • A qualifi ed installer should carry out the following Before using the oven, remove any protective checks: wrap from the stainless steel. • All stainless steel body parts should be wiped Range mounted on its legs with hot, soapy water and with a liquid stainless Island trim or Backguard attached accor-...
- Page 23 We have a dedicated team of trained professionals to answer your ne- eds. If you own a Bertazzoni appliance and need ser- vice in the US or Canada please use the following contact information: e-mail: aftersaleservice@bertazzoni.com Telephone - Monday through Friday, 7.30am to 7.30pm EST (except US public holidays).
- Page 24 ...
- Page 25 ...