2. Introduction
Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer
We hope your new tool brings you much enjoyment
and success.
Note:
In accordance with the applicable product liability
laws, the manufacturer of this device assumes no
liability for damage to the device or caused by the
device arising from:
• Improper handling
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised
specialists.
• Installing and replacing non-original spare parts,
• Improper use
• Failure of the electrical system in the event of the
electrical regulations and VDE provisions 0100,
DIN 13 / VDE0113 not being observed
Please consider:
Read the whole text of the operating manual before
assembly and commissioning.
This operating manual should help you to familiarise
yourself with your device and to use it for its intended
purpose.
The operating manual includes important instructions
for safe, proper and economic operation of the device,
for avoiding danger, for minimising repair costs and
downtimes, and for increasing the reliability and extend-
ing the service life of the device.
In addition to the safety instructions in this operating
manual, you must also observe the regulations appli-
cable to the operation of the machine in your country.
Keep the operating manual at the device, in a plastic
sleeve, protected from dirt and moisture. They must
be read and carefully observed by all operating per-
sonnel before starting the work.
The device may only be used by personnel who have
been trained to use it and who have been instructed
with respect to the associated hazards. The required
minimum age must be observed.
In addition to the safety instructions in this operating
manual and the separate regulations of your country,
the generally recognised technical rules relating to the
operation of such machines must also be observed.
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
30 | GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
3. Device description (fig. 1 - 3,
16 - 17, 19, 20, 23, 27, 29, 31, 36, 39)
1.
Saw blade
1a. Hexagon screw
1b. Outer saw blade flange
1c. Inner saw blade flange
2.
Saw blade guard
2a. Fixing screw
3.
Riving knife
3a. Fixing screw
4.
Table inlay
4a. Fixing screw
5.
Saw table
6.
Extraction hose
7a. Rear guide rail
7b. Front guide rail
8.
Parallel stop
8a. Guide rail
8b. Eccentric lever
8c. Hexagon screw
9.
Right table width extension
10. Push stick
11. Locking lever right table width extension
12. Scale
13. Wheel
14. Locking latch
15. On/off switch
16. Crank wheel
17. Overload switch
18. Locking lever
19. Transverse stop
19a. Screw clamp
19b. Guide rail
19c. Clamping handle
19d. Knurled nuts
19e. Wing nut for screw clamp
19f. Wing nut for transverse stop
20. Left table width extension
20a. Wing nuts
21. Sliding carrier plate
21a. Wing nut
22. Extraction port
23. Hose clamp for extraction hose
24. Machine stand
25a. Machine stand part 1
25b. Machine stand part 2
25c. Machine stand part 3
25d. Machine stand part 4
25e. Machine stand part 5
25f. Machine stand part 6
26. Ring spanner 10 / 13 mm
27. Ring spanner 10 / 21 mm
28. Groove
29. Sight glass
30. Wooden push block (not included in the scope
of delivery)