Technics SL-1000R Manuel D'utilisation page 15

Operation and display of the control unit
Display dimmer setting
The display dimmer will be activated if the
control unit is not operated for 20 seconds.
There are four dimming patterns.
1
On the control unit, hold [RESET]
down and press [DISPLAY].
z The dimmer setting is displayed.
2
Press [DISPLAY] on the control unit.
The setting changes each time [DISPLAY] is
pressed. (See below.)
z The display returns to the original display
if no operation is performed within three
seconds.
33
33.33
[RESET][DISPLAY]
Display OFF
(Initial setting)
[DISPLAY]
Dimmer OFF
[DISPLAY]
Dimmer 1
[DISPLAY]
Dimmer 2
Display dimmer when no operation
Display
is performed for 20 seconds
Brightness is reduced by one level.
⇒ (No operation for further five seconds)
⇒ Brightness is reduced by two levels.
Display OFF
⇒ (No operation for further five seconds)
⇒ Off
Dimmer OFF No dimming (Always on)
Dimmer 1
Brightness is reduced by one level.
Dimmer 2
Brightness is reduced by two levels.
z After setting, brightness is immediately adjusted
to the set value. The display is immediately turned
off if "Display OFF" is selected.
z Operating a button (any button other than
the power button) on the control unit while
the dimmer is active returns the display to full
brightness.
Note
z The setting is saved. When the power is turned on
the next time, the setting when the power was
turned off last will be recovered.
28
(28)
English
(continued)
Adjusting the torque to rotate
the turntable at a constant speed
Press [START·STOP] and then adjust the torque
(rotational force) at five levels to rotate the
turntable at a constant speed.
1
On the control unit, hold [RESET]
down and press [-] and [+]
simultaneously.
z The torque setting is displayed.
2
Press [-] or [+] on the control unit
to make adjustment.
z Select one of the five levels from
"TORQUE1" to "TORQUE5".
Pressing the button increases or
decreases the value.
z Use the table below as a guide.
z The display returns to the original display
if no operation is performed within three
seconds.
33
33.33
[RESET][ ー ][ ＋ ]
TORQUE 5
(Initial setting)
↑
[+] [-]
TORQUE 1
Torque to rotate at a
Display
constant speed
TORQUE5 Maximum (Initial setting)
TORQUE4
TORQUE3
TORQUE2
TORQUE1 Minimum
Note
z The setting is saved. When the power is turned on
the next time, the setting when the power was
turned off last will be recovered.
Maintenance
Care of the parts
„
Thoroughly clean dust off the stylus and
record.
z Take off the head shell with the cartridge and
clean the stylus using a soft brush.
Brush from the base to the tip.
z Use a record cleaner to keep your records
clean.
Head shell
terminals
Wipe the head shell terminals occasionally.
Wipe the head shell terminals with a soft cloth
and fit the head shell to the tone arm.
Turn the amplifier volume down or turn the
amplifier off before fitting or removing the
head shell.
Damage to your speakers can occur if the head
shell is moved while the volume is turned up.
Cleaning the dust cover and
„
cabinet
Wipe the dust cover and cabinet with a soft
cloth.
When dirt is heavy, wring a wet cloth tightly to
wipe the dirt, and then wipe it with a soft cloth.
z Do not use solvents including benzene,
thinner, alcohol, kitchen detergent, a
chemical wiper, etc. This might cause the
exterior case to be deformed or the coating
to come off.
z Do not wipe the dust cover while playing a
record.
This can cause static electricity. This static can
cause the tone arm to be attracted towards
the dust cover.
Moving the unit
„
Repackage the unit in the packaging it came
in. ( 12)
Keep the packaging materials after taking out
the goods.
If you no longer have the packaging, do the
following:
z Take off the turntable and turntable mat and
carefully wrap them.
z Remove the head shell and balance weight
from the tone arm and carefully wrap them.
z Clamp the tone arm with the arm clamp and
tape it in place.
z Carefully wrap the main unit in a blanket or
paper.
Repackaging
Before repackaging,
remove the balance
weight and insert the
tone arm support under
the tone arm.
WEEE symbol
„
Disposal of the product outside the EU
countries
This symbol is valid within the EU
only.
Contact a local governmental office
or your dealer to confirm a right
manner of disposal.
(29)
English
29