Chicco I-move Mode D'emploi page 24

- rotating the seat (diag. 13A front-facing, diag. 13B par-
ent-facing)
- inverting the handlebar (diag. 13C front-facing, diag.
13D parent-facing)
ROTATING THE SEAT
WARNING: When performing the operations illustrated
below, always place the stroller on a flat even surface and
remove any weights attached to the handlebar to avoid
compromising its stability.
To switch from parent-facing mode to front-facing mode,
or vice-versa, apply the brakes and proceed as follows:
14. Release both snap-clasps on the handle simultane-
ously, and move the hand grip section upwards, as seen
in diagram 14.
15. Use your foot to release the rotation lock pedal as
seen in diagram 15.
16. The seat can now be rotated in either direction (diag.
16A). Select the user mode (parent-facing or front-facing)
and pull the handlebar back towards you (diagram 16B).
INVERTING THE HANDLEBAR
The user mode can also be switched by simply inverting
the handlebar.
WARNING: remove all weights attached to the handle-
bar.
Apply the stroller brake and proceed as follows:
17. Release both snap-clasps on the handle and move
the hand grip section to the opposite side until it locks in
place (diagram 17).
WARNING: when the stroller is used in this user mode,
the swivel wheel option must be blocked (see "swivel
wheels" paragraph)
WARNING: the stroller may become slightly less easy to
manoeuvre when used in this mode.
RECLINING THE BACKREST
18. Pull the button (A) on the stroller backrest to recline it
to the position you need (diagram 18). Release the button
and the backrest will click into the closest lock position.
Simply push the backrest upwards to raise it again.
WARNING: these operations can become more difficult
when the child is sat in the seat.
LEG-REST / FOOT-REST
The stroller is fitted with a practical adjustable leg-rest/
foot-rest.
19. To adjust the leg-rest/foot-rest, use the two buttons
located on each side of the leg-rest, as indicated in dia-
gram 19, until you find the right position. It is not neces-
sary to press the buttons to raise the leg-rest/foot-rest
again.
BUMPER BAR
20. To assemble the bumper bar, slide the side pins into
the slots and push them all the way in (diagram 20).
21. Rotate the bumper bar to an upright position and press
it downwards until you hear it click into place (diag. 21).
22. To remove the bumper bar, press the button indicated
in diagram 22A and pull it upwards. Then pull the bumper
bar into a horizontal position.
This position can be used to make it easier to place the
baby inside the stroller.
To remove the bumper bar completely, pull it until it
slides out of the slots on the seat (diag. 22B).
WARNING: Always restrain the child using the safety har-
ness. The bumper bar is NOT a child restraint device.
WARNING: never use the bumper bar to lift the stroller up.
HAND GRIP
The hand grip can be adjusted in height.
23. Release the adjuster levers on the sides of the hand
grip, as seen in diagram 23, and adjust the handlebar to
the desired height. Lock the adjuster levers in place.
SWIVEL WHEELS
The stroller has swivel/fixed front wheels. It is recom-
mended to use the fixed wheels on particularly uneven
ground. It is recommended to use the swivel wheels on
normal road surfaces as it makes it easier to manoeuvre.
24. To switch the front wheels to swivel mode, press the
front button with your foot, as seen in diagram 24. To
switch back to fixed mode, press the same button again
with your foot. Whatever the current position of the
wheel, it will lock in a straight position.
WARNING: Both wheels must be locked or unlocked at
the same time.
WARNING: When using the stroller with the swivel wheels
at the back, they must be locked in the fixed mode.
REMOVING THE SEAT
WARNING: when closing the stroller, make sure that your
child and all other children are at a safe distance. Ensure
that during these operations the moving parts of the
stroller do not come into contact with your child.
25. To remove the seat, raise the backrest to an upright
position. Use one hand to press the backrest adjuster but-
ton, and the other to press the triangular shaped orange
button at the bottom of the backrest (Diag. 25A). Push
the backrest forward towards the seat until the first set of
fasteners are released. The seat can now be rotated all the
way towards the front section of the stroller (Diag. 25B).
Pull the orange handle located under the seat to remove
it from the frame (Diag. 25C).
CLOSING THE STROLLER
WARNING: when closing the stroller, make sure that your
child and all other children are at a safe distance. Ensure
that during these operations the moving parts of the
stroller do not come into contact with your child.
Position the stroller in front-facing mode, as seen in dia-
gram 13A.
26. Release the metal hinges as seen in diagram 26 and
fold the hood; then follow the instructions provided in
sections 25A and 25B.
27. Shorten the handle making it more compact (1). Re-
lease both snap-clasps on the handle and turn the hand
grip (2) to the position illustrated in diagram 27.
Press the open/close lever to fold the stroller, as illustrat-
ed in diagram 3.
28. Lift the handgrip up so the rear wheels approach the
front wheels and lock in place (diag. 28).
Attention: we recommend closing the handlebar towards
the front wheels to make it more compact when folded.
29. To make the frame even more compact, you can also
remove the seat from the frame by pressing the orange
lever located under the seat (diag. 25C) as illustrated in
diagram 29.
USING THE CHILD CAR SEAT AND CARRYCOT
The I-MOVE carrycot and the I-MOVE car seat can also be
assembled on the CHICCO I-MOVE stroller frame. Please
consult the relative instructions for information on how
to fit and remove the carrycot or child seat.
WARNING: only the CHICCO I-MOVE child car seat and
carrycot can be fastened onto the I-MOVE stroller. Be-
fore using the stroller in combination with the carrycot
or child car seat, always check that the hook-on system
is correctly closed and locked in place. ONLY USE ACCES-
SORIES FITTED WITH THE RELATIVE I-MOVE HOOK-ON
DEVICE.
24