HP DesignJet Z6dr Instructions D'assemblage
Masquer les pouces
Voir aussi pour DesignJet Z6dr:
- Guide d'utilisation (232 pages) ,
- Informations d'introduction (101 pages)
Publicité
Liens rapides
HP DesignJet Z6
Printer Series
Assembly instructions
EN
Instructions d'assemblage
FR
Anleitung zum Zusammenbau
DE
Istruzioni per l'installazione
IT
Instrucciones de montaje
ES
Instruções de montagem
PT
Instructies voor het opstellen
NL
تعليمات التجميع
AR
*T8W18-90046*
T8W18-90046
© Copyright 2018 HP Development Company, L.P.
Large Format Division
Camí de Can Graells 1-21 · 08174
Sant Cugat del Vallès
Barcelona · Spain
All rights reserved
Printed in XXX
Hardware Setup:
EN
1- Assemble the stand
2- Attach the printer body to the stand assembly
3- Set up the printer
4- Printhead and cartridge setup
5- Connectivity & Mobile Printing
Software setup:
Now, it's easy to print large-format documents from virtually anywhere,
using your laptop, printer touchscreen, iPhone®, or iPad®.
Install the product software from www.hp.com/go/Z6/drivers
Installation du matériel :
FR
1- Assemblage du support
2- Fixation de l'imprimante au support
3- Configuration de l'imprimante
4- Installation des têtes d'impression et des cartouches
5- Connectivité et impression mobile
Installation du logiciel :
Il est désormais facile d'imprimer des documents grand format depuis
quasiment n'importe où à l'aide d'un ordinateur portable, de l'écran tactile
de l'imprimante, d'un iPhone® ou d'un iPad®.
Installation du logiciel du produit à partir de www.hp.com/go/Z6/drivers
DE
Hardware-Setup:
1- Zusammenbauen des Standfußes
2- Aufsetzen des Druckers auf den
Standfuß
3-Einrichten des Druckers
4- Einrichten von Druckköpfen und Patronen
5- Verbindung und HP Mobile Printing
Software-Setup:
Das Drucken großformatiger Dokumente von nahezu jedem Standort aus
mit Ihrem Notebook, Drucker-Touchscreen,
iPhone® oder iPad® ist nun einfacher denn je.
Installieren Sie die Produktsoftware von: www.hp.com/go/Z6/drivers
IT
Installazione dell'hardware:
1- Assemblaggio del piedistallo
2- Fissare il corpo della
stampante al piedistallo
3-Installazione della stampante
4 - Installazione delle cartucce e delle testine di stampa
5- Connettività e soluzioni "mobili" per la stampa
Impostazione del software:
Ora è semplice stampare documenti di grande formato da praticamente
qualsiasi posizione utilizzando il laptop, lo schermo a sfioramento della
stampante, l'iPhone® o l'iPad®.
Installare il software del prodotto da: www.hp.com/go/Z6/drivers
1
Instalación del hardware:
ES
1- Montaje del soporte
2- Una la estructura de la
impresora al conjunto del soporte
3-Configuración de la impresora.
4- Instalación del cabezal de impresión y el cartucho
5-Conectividad e impresión desde dispositivos móviles
Instalación del software:
Ahora resulta muy fácil imprimir documentos de gran formato desde
prácticamente cualquier lugar mediante un portátil, la pantalla táctil de
la impresora, un iPhone® o un iPad®.
Instale el software del producto desde: www.hp.com/go/Z6/drivers
PT
Configuração de hardware:
1- Monte a base
2- Conecte a impressora à
montagem da base
3- Instalar a impressora
4 - Configuração de cartucho de tinta e cabeçotes de impressão
5- Conectividade e impressão móvel
Configuração de software:
Agora, é fácil imprimir documentos em grandes formatos de
praticamente qualquer lugar usando o laptop, a tela sensível ao toque
da impressora, o iPhone® ou o iPad®.
Instale o software do produto pelo site: www.hp.com/go/Z6/drivers
NL
Installatie van de hardware:
1- De voet in elkaar zetten
2- Bevestig het hoofdbestanddeel van de printer aan de gemonteerde
staander
3- De printer opstellen
4- Installatie van printkop en cartridge
5- Connectiviteit en mobiel afdrukken
Installatie van de software:
Nu kunt u eenvoudig documenten van groot formaat vanaf vrijwel elke
locatie af te drukken, met behulp van uw laptop,
uw printertouchscreen, iPhone® of iPad®.
Installeer de product software via: www.hp.com/go/Z6/drivers
"2 - تثبيت جسم الطابعة بتجميع
4 - تعيين إعدادات الخرطوشة و ر أس الطباعة
5 - االتصال والطباعة باستخدام األجهزة المحمولة
أصبح اآلن من السهل طباعة المستندات ذات التنسيقات
الكبيرة أينما كنت باستخدام الكمبيوتر المحمول أو شاشة
اللمس الموجودة في الطابعة أو
:قم بتثبيت البرنامج الخاص بالمنتج من
www.hp.com/go/Z6/drivers
:إعداد الجهاز
AR
1 - تجميع الحامل
الحامل
3 - إعداد الطابعة
:إعداد الب ر نامج
أو
.
®iPhone
®iPad
Publicité
Manuels Connexes pour HP DesignJet Z6dr
Sommaire des Matières pour HP DesignJet Z6dr
- Page 1 Configuração de software: Agora, é fácil imprimir documentos em grandes formatos de Installation du logiciel du produit à partir de www.hp.com/go/Z6/drivers praticamente qualquer lugar usando o laptop, a tela sensível ao toque da impressora, o iPhone® ou o iPad®.
- Page 2 • Le temps requis pour l’assemblage de l’imprimante est d’environ 110 minutes. Remarque : Rouleau et câbles LAN non inclus. • Pour télécharger les pilotes d’imprimante, rendez-vous à l’adresse suivante : www.hp.com/go/Z6/drivers Standort des Produkts Lesen Sie diese Anleitungen sorgfältig durch. Dieses Dokument enthält Anleitungen für den Zusammenbau des Druckers.
- Page 3 Assemble the stand Assemblage du support Zusammenbauen des Standfußes Assemblaggio del piedistallo Montaje del soporte Monte a base De voet in elkaar zetten تجميع الحامل 40’ Place the cross brace on the floor with the letters L and R Fix one foot to a leg with 8 screws. Locate the stand pieces and remove the following: 1.
- Page 4 Slot the other leg onto the cross brace making sure that the Fix the leg to the cross brace with 3 screws at the inner Slot a leg onto the cross brace to install the leg with the long Fix the leg to the cross brace with 3 screws at the inner basket supports located on the feet (1 on each foot) are on the side of the foot as shown in the image.
- Page 5 ثبت الجزء الخارجي من الرجل بالعارضة باستخدام يفترض أن يكون معك مسماريين إضافيين حالي ً ا. أحكم ربط ثبت : قياس 44 بوصة فقطHP DesignJet Z6 مع طابعة .أدر الحامل في وضع عمودي .مسمارين. كرر العملية مع الرجل األخرى .مسامير الحامل بالاكمل...
- Page 6 Attach the printer body to the stand assembly Fixez l’imprimante à l’assemblage du support Anbringen des Druckers auf dem Ständer Fissare il corpo della stampante al gruppo del piedistallo Coloque el cuerpo de la impre- sora en el montaje del soporte Acople o corpo da impressora na montagem do suporte To finish the stand assembly check that the 4 wheels are...
- Page 7 There is a round yellow button protruding from the top of Remove the tape from the transparent covering that Open the transparent covering and remove the desiccant Remove the small flaps from each of the foam end pieces. one stand leg, and a square green button protruding from protects the product.
- Page 8 Locate the 4 black screws. Fix the printer to the stand from underneath with the 4 Check that the wheels on the stand are locked. Place the stand on the product slowly and carefully, so that black screws. the colored buttons on the legs fit into the corresponding holes in the product.
- Page 9 Remove the foam end pieces. Remove the transparent covering from the product. Make sure there is nothing on the printer. Hold the product by the foam end pieces and rotate it until Rotate the product 90°. it stands on its feet, with all four wheels in contact with the IMPORTANT: While you rotate, keep the roll feeds face down- floor.
- Page 10 Remove the tape from the stand, and unfold the fabric. Pass the fabric through to the front of the printer and then Install the pocket at the back of the printer. Clip the basket frame to the feet. Press firmly until it clicks insert the frame.
- Page 11 فقط: افتح غطاءHP DesignJet Z6dr PostScript طابعة افتح اإلطار .الموجودة بداخل المنتج القواطع العمودية، وتأكد من أن القواطع العمودية تقع على فقط: قم بإ ز الةHP DesignJet Z6dr PostScript طابعة الشريط .الورق المقوى على أسطوانة اإلخ ر اج...
- Page 12 90º 90º Carefully lift the cardboard support up and out of the Inside the right-hand side of the product, you will see a piece You will see a cardboard support attached to the product Turn the cardboard support 90° to the right. of cardboard.
- Page 13 7-15’ If you find a USB flash drive in a plastic bag inside the box, it Connect the network cable. Remove the cardboard carefully. It will not be needed again Remove the orange tapes and unlock the wheels. Move the contains the latest Firmware.
- Page 14 Connect the power cable to the printer, and the outlet. On the front panel, the HP logo appears. Please wait a while. Remove the plastic film covering the window and the plastic You will then be prompted to select the language of the film covering the front panel (LCD display).
- Page 15 Printhead and cartridge setup Installation des têtes d’impression et des cartouches Einrichten von Druckköpfen und Patronen Installazione delle cartucce e delle testine di stampa Instalación del cabezal de impresión y el cartucho Configuração de cartucho de tinta e cabeçotes de impressão Installatie van printkop en car- Insert the ink cartridges one-by-one (x6).
- Page 16 10’ The printer now prepares the ink system for use. When the ink system is ready, the front panel will prompt Open the window and pull the blue printhead cover handle Push the handle back to raise the lid to access the setup Please wait until it has completed before you continue.
- Page 17 Look at each setup printhead to verify that it has ink inside. When all of the setup printheads have been removed, press Unwrap each printhead and remove all orange parts. Remove and discard all the setup printheads. You may need The setup printheads only purpose is to prevent ink loss to use force to extract each printhead.
- Page 18 Pull the handle down to close the cover. Ensure that the end of the blue handle catches the wire loop The printhead is designed to be inserted into any available slot. Insert the printheads one by one. Push each printhead into Once the printhead is inserted into a slot it sets up to work only the slot until it clicks into place.
- Page 19 10’ Close the top cover. The product checks and prepares the If the blue removable stop is on the spindle, remove it. Load Once the printhead check has finished the product will be When the front panel prompts you to load paper for printhead the roll onto the spindle as indicated in the image.
- Page 20 Feed the leading edge of the paper into the product until the The product will proceed to align the printheads. This process Add the removable stop to the spindle to keep the roll in From the front of the product, place the spindle into the involves printing, and therefore needs to use paper with a product.
- Page 21 Load the roll onto the spindle. Follow the steps 65 and 66. The front panel will display a series of messages showing the HP DesignJet Z6dr PostScript Printer only: Paper load on lower progress of the printhead alignment. There is no need to take roll;...
- Page 22 Feed the leading edge of the paper into the product until the From the back of the product, place the spindle into the product takes hold of it. Then move to the front of the product. product. Note: do not close the roll cover until the front panel notifies you.
- Page 23 3- Con las soluciones de impresión móvil HP puede imprimir directamente desde su smartphone o tablet en tres 3-With HP Mobile Printing Solutions you can print straight from your smartphone or tablet in just a few simple steps pasos sencillos desde donde se encuentre; con el sistema operativo del dispositivo móvil o enviando un correo wherever you are;...
- Page 24 البريد اإللكتروني الخاص بالطابعة للطباعة عبر البريد اإللكتروني وتجنب التجارب المتكررة مع التحقق من األخطاءHPGL/2 وTiff وJPEG وPDF بم ز ايا االكتشاف التلقائي للطابعات والتجهيز السريع لملفات www.hp.com/go/designjetclick : ومعاينة الطباعة في الوقت الفعلي. قم بالتنزيل منPDF في...
- Page 25 - Per la stampa in Android, installare il componente aggiuntivo HP Print Service da Google Play. . لتعزيز قد ر ات الطباعة لديك من هاتف ذكي أو كمبيوتر لوحيHP Smart App -نك أيض ً ا تحميل تطبيق - È inoltre possibile scaricare l’app HP Smart App (iOS/Android) per ottimizzare le capacità di stampa da uno smartphone o http://www.hp.com/go/designjetmobility :لمزيد...
- Page 26 If you are the printer administrator you can change the status to lock mode, customize your printer’s email address, or manage the printer security (you will need the printer code and an account at HP Connected.
- Page 28 ويجب عدم اعتبار أي مما ورد في هذه الوثيقة على أنه بمثابة ضمان © Copyright 2018 HP Development Company, L.P. مسؤوليتها عن أية أخطاء فنية أو تحريرية أو أيةHP إضافي. تخلي شر كة .أخطاء ناتجة عن الحذف وردت في هذا المستند...