Technical Data; Noise/Vibration Information; Battery Charging; Dust/Chip Extraction - Bosch PKS 18 LI Notice Originale

(28) 45° cut mark
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Handheld circular saw
Article number
Rated voltage
A)
No-load speed
Max. cutting depth
– at a 0° mitre/bevel angle
– at a 45° mitre/bevel angle
Base plate dimensions
Saw blade diameter
Max. base blade thickness
Max. tooth thickness/offset
Min. tooth thickness/offset
Locating bore
Weight according to EPTA-
A)
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Recommended batteries
C)
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-5.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 88 dB(A); sound power level
99 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-5:
2
Sawing wood: a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
Bosch Power Tools
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
PKS 18 LI
over the total working period.
3 603 CB1 3..
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
V 18
power tool and application tools, keeping their hands warm,
-1
min 4300
and organising workflows correctly.
mm 48
Fitting
mm 36
u
mm 133 x 244
mm 150
mm 1.4

Battery Charging

mm 2.0
u
mm 1.5
mm 16
kg 2.7 kg (1.5 Ah) –
Note: The battery is supplied partially charged. To ensure
3.1 kg (6 Ah)
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
°C 0 to +35
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
°C -20 to +50
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
PBA 18V...W-.
is discharged, the power tool is switched off by means of a
AL 18...
protective circuit: The application tool no longer rotates.
u
Follow the instructions on correct disposal.
Removing the battery (see figure A)
To remove the battery (3), press the release button (17)
and pull the battery upwards and out of the power tool. Do
not use force to do this.

Dust/chip extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
2
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
Only use saw blades the maximum permitted speed of
which is higher than the no-load speed of the power
tool.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
terial wherever possible.
1 609 92A 4SL | (07.08.2019)
English | 17