Product Description And Specifications; Intended Use; Product Features - Bosch PKS 18 LI Notice Originale

16 | English
Always observe that the lower guard is covering the
u
blade before placing the saw down on bench or
floor.An unprotected, coasting blade will cause the saw
to walk backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop after
switch is released.
Additional safety warnings
Do not allow the chip ejector to come into contact with
u
your hands. You may be injured by rotating parts.
Do not use the saw above the level of your head. Doing
u
so will mean you have inadequate control of the power
tool.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Do not operate the power tool when stationary . It is
u
not suitable for operation with a saw table.
When performing plunge cuts which are not right-
u
angled, secure the guide plate of the saw so that it will
not shift sideways.In the event of a sideways shift, the
saw blade may become jammed, which could lead to kick-
back.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Do not use HSS saw blades. Such saw blades can easily
u
break.
Do not saw any ferrous metals. Hot chips may ignite the
u
dust extractor.
Wear a dust mask.
u
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
1 609 92A 4SL | (07.08.2019)
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for making straight cuts in wood
with and against the grain and mitre cuts in wood while rest-
ing firmly against the workpiece.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Lock-off button for on/off switch
(2) On/off switch
A)
(3) Battery
(4) Extraction outlet
(5) Protective guard
(6) Adjusting lever for retracting blade guard
(7) Base plate
A)
(8) Circular saw blade
(9) Retracting blade guard
(10) Parallel guide
(11) Wing bolt for parallel guide
(12) Viewing window for "Cut Control"
(13) Wing bolt for mitre/bevel angle preselection
(14) Scale for mitre/bevel angles
(15) Auxiliary handle (insulated gripping surface)
(16) Handle (insulated gripping surface)
(17) Battery release button
A)
(18) Extraction hose
(19) Spindle lock button
(20) Saw spindle
(21) Mounting flange
(22) Clamping flange
(23) Clamping bolt with washer
(24) Hex key
(25) Wing bolt for preselecting the cutting depth
(26) Cutting depth scale
(27) 0° cut mark
Bosch Power Tools