Technical Data; Noise Information - Bosch Professional GCM 216 Notice Originale

(15) Locking knob for various mitre angles
(16) Mitre pre-setting lever
(17) Angle indicator for mitre angles
(18) Scale for mitre angles
(19) Mounting holes
(20) Recessed handles
(21) Extension bar
(22) Screw clamp
(23) Adjustable fence
(24) Scale for bevel angle
(25) Angle indicator (vertical)
(26) Guide roller
(27) Chip deflector
(28) Spindle lock
(29) On/off switch
(30) On/off switch for laser (cutting line indication)
(31) Chip ejector
(32) Hex key
(33) Clamping handle for various bevel angles
(34) Transport safety lock
(35) Holes for screw clamp
(36) Wing bolt for fixing the guide rail for length gauge
(37) Guide rail for length gauge
(38) Securing screw for extension bar
(39) Hex socket screw for mounting the saw blade
(40) Clamping flange
(41) Saw blade
(42) Inner clamping flange
(43) Wing bolt for fixing the adjustable fence
(44) Wing bolt for adjusting the height of the threaded
rod
(45) Threaded rod
(46) Clamping screw for length gauge
(47) Screws for insert plate
(48) Hex socket screw for fence
(49) Screw for mitre angle indicator
(50) Knurled screw for laser protection cap
(51) Laser lens cover

Technical Data

Mitre saw
Article number
Rated power input
No-load speed
Laser type
Bosch Power Tools
Mitre saw
Laser class
Divergence of laser line
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Max. cutting width
Hole diameter
Permitted workpiece dimensions (maximum/minimum): (see "Per-
missible workpiece dimensions", page 27)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
The appliance meets IEC 61000-3-11 requirements and is
subject to conditional connection. The appliance can lead to
occasional voltage fluctuations under unfavorable power
conditions. The impedance of this appliance is set as Z
= 0.35 Ω. The user must make sure, that the connection
point, with the impedance Z
be plugged in meets the impedance requirement: Z
≥ Z
tual
with the network supplier or supply authority.

Noise Information

Noise emission values determined according to
EN 62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 96 dB(A); sound power level
106 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
GCM 216
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
3 601 M33 0..
ficantly reduce noise emissions over the total working
W 1300
period.
-1
min 4800
nm 650
mW < 1
mrad
angle)
, on which the appliance shall
max
. If Z is unknown, determine Z
max max
1 609 92A 72R | (15.11.2021)
English | 23
GCM 216
2
1.0
(full
kg 9.1
/ II
mm 216
mm 1.4−1.8
mm 3.3
mm 30
actual
ac-
in consultation
max