Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
20 | English
(61)
Cross-head screw for setting the 0° stop
(62)
Stop for 0° bevel angle
(63)
Screw for bevel angle indicator
(64)
Cross-head screw for setting the 45° stop
(65)
Stop for 45° bevel angle
(66)
Hex socket screws (5 mm) on the front for adjust-
ing the parallelism of the saw blade
(67)
Hex socket screws (5 mm) on the rear for adjust-
ing the parallelism of the saw blade
(68)
Screw for saw table spacing indicator
(69)
Hex socket screws (5 mm) for adjusting the paral-
lelism of the parallel guide
Table saw
Article number
Rated power input
Rated voltage
Frequency
No-load speed
Starting current limitation
Weight according to EPTA-
Procedure 01:2014
Protection class
Dimensions (including detachable parts of the tool)
Width x depth x height
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Min. tooth thickness/offset
Hole diameter
Maximum workpiece dimensions: (see "Maximum workpiece dimen-
sions", page 25)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Table saw with fitted saw blade (27) and riving knife (8)
– Angle guide (3)
– Profile rail (29)
– "Profile rail" fastening set (46) (guide plate, knurled nut,
screw, washer)
1 609 92A 6YX | (01.09.2021)
(70)
Screw for parallel guide spacing indicator
(71)
Adjusting screws for table insert
(72)
Bracket for storing the "additional parallel guide"
fastening set
(73)
Holding clip for storing the dust extraction adapter
(74)
Bracket for storing the anti-kickback pawls
(75)
Securing nut for the ring spanner and for hanging
the push stick
(76)
Bracket for storing the hex key
(77)
Holding clip for storing the angle guide
a) Country version 3 601 M30 5C2
Technical Data
GTS 10 J
3 601 M30 5..
W
1800
V
220−240
Hz
50/60
min
-1
3650
kg
26.2
mm
640 x 706 x 330
mm
254
mm
< 2.2
mm
> 2.4
mm
25.4
– Parallel guide
– Additional parallel guide (43)
– "Additional parallel guide" fastening set (44) (3 fastening
screws, 3 washers, 3 wing nuts)
– Protective cover (6)
– Anti-kickback pawls (9) (Country version
3 601 M30 5C2 )
– Hex key (22)
– Hex key (21)
– Ring spanner (23)
– Push stick (24)
– Table insert (26)
– Dust extraction adapter (33)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
a)
GTS 10 J
3 601 M30 5C2
1700
120
60
3700
●
26.2
/ II
/ II
640 x 706 x 330
254
< 2.2
> 2.4
25.4
Bosch Power Tools
●
Publicité
Table des Matières
