stayer SC250W Instructions D'emploi page 38

This manual is consistent with the date of
manufacture of your machine, you will find
information on the technical data of the machine
acquired manual check for updates of our machines
on the website:
www.grupostayer.com
1.Provided uses of the machine
This tool has been solely and exclusively provided
for:
1.Stationary works on flat and stable surface
2.Working on hard and soft wooden pieces
3.Working on chipboard pieces
4.Working on fiberboard pieces
5.Working on PVC tubes
6.Making rectilinear cuts along the length and width
of the workpiece
7.Making horizontal mitre-cuts between -45º and
45º.
Making vertical mitre-cuts between 90º and 45º
Refer to the limits regarding the size of the
workpiece in corresponding chapter 11.
2.Unpackaging and assembling
Unpackaging
1.Cut the seal and open the box.
2.Withdraw upper cardboard stoppers
3.Extract the box by firmly grasping the operating
head and the motor body using both hands so as
to balance the weight
4.Extract the box with the accessories
5.Extract the documentation
6.Preserve the cardboard box, the stoppers thereof
and the documentation permanently in an
inventoried safe environment being easily
accessible and known to the machine operator.
Packaging
IMAGES A B V
Operation 1: Securing, folding and fastening
the operating head:
1.Place upper head at horizontally 0º acting on 8 or
14.
2.Place upper head at vertically 90º acting on 15.
3.Arrange protector 34 such that it contacts the
cutting bench.
4.Fix protector 34 by means of the frontal wing nut
24.
5.Push upper blocking button 29 to release the
descent of the head.
6.Lower head to the limit and position it to be able to
lock it with button 31.
7.Push lower locking button 31 to lock the head.
Operation 2: Packaging the machine
1.Locate the cardboard box.
2.Locate documentation.
ENGLISH
28
3.Firmly grasp the machine by its operating head
and motor body.
4.Place the machine over the 4 circular recesses of
the bottom of the box.
5.Store documentation of the machine.
6.Position upper cardboard stoppers.
Close the box and fix it with sealing tape.
3.Setting or fastening the
machine in a stable position
1.The working area where the machine is being
arranged must mandatorily be safe.
2.Support tool in a stable position on an even
surface.
3.The base of the mitre saw has four holes for firmly
fastening the machine to the working bench. It is
strongly recommended to fix the machine to the
bench by means of the pertinent screws and nuts.
4.Connection to the grid, wiring,
fuses, socket type for the jack and
requirements for grounding
1.For supplying electrical power to the machine,
connect the Schuko Jack to a standard socket
capable of supplying a minimum of 2500 VA .
2.The internal wiring of the machine is completely
terminated so that no wiring is needed when
installing it.
3.The machine does not have fuses although the
use of a dedicated magnetothermal switch is
recommended as a protection for the machine.
4.The machine has a class II electrical equipment
so that it does not make use of the grounding of
the electrical installation.
5.Illustrated description of
functions
1.Casing
2.Connecting/disconnecting switch
3.Locking button for continuous operation
4.Grip
5.Tiltable guard hood
6.Lower cutting table
7.Scale for horizontal mitre angle
8.Horizontal locking button for discretionary mitre
angles
9.Indicator for horizontal angles
10.Locking holes for fixed mitre angles
11.Machine fastening holes
12.Clamp anchor holes for fastening the workpiece
13.Stopper guide
14.Anchor bolt for horizontal locking for fixed mitre
angles
15.Lever for vertical locking for discretionary mitre
angles
16.Screw for vertical adjustment for fixed mitre
angles at 45º
17.Nut for vertical adjustment for fixed mitre angles
at 45º
28