Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
HOW TO ESTABLISH
Notice: Two speakers must be same model and both compatible with TWS.
1. Please switch on both speakers and select "Bluetooth" mode;
2. Press "TWS" button (7) of one of the speakers until hearing a "beep". It becomes the main speaker (left chennel), which will
automatically search and connect with another speaker (right channel). After connection, you will hear a "beep";
3. Connect mobile phone or Bluetooth player to the speaker by Bluetooth. After connection, you can play music with the TWS
Stereo- Speaker System.
TWS function operates in TWS mode, manipulations to the main speaker will be simultaneously effected in another speaker. For
example, volume adjustement, previous and next song selection, play and pause, power on and off.
Note:
-
If the 2 loudspeakers are not paired, switch off both devices and repeat steps 1, 2 and 3.
-
The TWS function only works between equal speakers or with other speakers that use the same micro processor or solution.
USB/ MICRO SD INPUT
1. Switch On the appliance;
2. Insert a USB memory or an Micro SD card in the corresponding entries (16/17). Playback starts automatically;
3. To pause playback, press the
"PAUS";
4.
To resume
playback, press the
:
5. Press
(11) button on unit
9
Press the
(9) button on unit
6. Using the numeric keypad (14) on remote control you can directly enter the number of the song you want to play;
7. Press
button (8) on remote control, the display will show "ONE" (to reproduce the same track continuously); press it
a second time, the word "ALL" will appear on the display (to continuously play all the tracks contained in the USB/Micro SD
device);
8. Use the FL- (2) and FL + (7) buttons on the remote control to select the folder (if any) containing the desired tracks.
Note:
-
The player may not support some USB/Micro SD devices, this is due to the incompatibility of some processors.
-
To avoid harmful interference, always connect USB devices directly to the unit, do not use extension cords.
-
From the computer to format the USB memory/SD FAT (16 or 32).
AUX-IN
1. Switch on the unit and select the "AUX" function;
2. Connect any unit equipped with audio output, through a cable 3.5mm jack to the AUX IN (15);
3. Use the external device from their commands.
USING THE WIRELESS MICROPHONE
1. Remove the cover on the back of the Microphones, insert 2 "AA" batteries into each microphone paying attention to the
polarities indicated and close the cover again;
2. Turn on the microphone by moving the center switch upward. If the power indicator flashes or does not light up, check if the
batteries are charged and if they have been inserted with the correct polarity;
3. Adjust the volume by turning the MIC VOL knob (3);
4. If the power indicator flashes after the microphone is turned on, the batteries are exhausted, replace them immediately.
Note:
-
The effective range of the wireless microphone is 15m. Do not use over that range.
-
Do not use two microphones working on the same frequency or crosstalk and interference will occur.
-
If you use more wireless microphones at the same time, they must be set to different frequencies and should be kept away at
least at 30m.
-
Don't put the device too close to a DVD/CD/VCD player as they have strong frequencies and might affect the microphone.
POSSIBLE LIMITATIONS OF USE
-
This device may operate on unauthorized frequencies in the region where the user is located. We recommend that you con-
tact the competent authorities and request the necessary information relating to the frequencies authorized in your region for
wireless microphone systems. In some cases, a ministerial license may be required for the use of this appliance. For possible
(10) button on the unit or the key
(10) on the unit or on the remote control (11);
:
or
(12) button on remote control while listening to switch to the next track.
9
or
(4) button on remote to go to the previous tracks;
(11) on remote control, the display will show
15
XF 1560 KB
Publicité
