Nuna triv next Mode D'emploi page 10

Product Information
Model Number: _____________________________________________________________________________
Manufactured Date: ________________________________________________________________________
Warranty
We have purposely designed our high-quality products so that
they can grow with both your child and your family. Because we
stand by our product, our gear is covered by a custom warranty
per product, starting from the day it was purchased. Please have
the proof of purchase, model number and manufactured date
available when you contact us.
For warranty information please visit:
www.nunababy.com
Click the "Warranty" link on the homepage.
Contact
For replacement parts, service, or additional warranty questions,
please contact our customer service department.
info@nunababy.com
www.nunababy.com
NUNA International B.V.
Van der Valk Boumanweg 178 C
2352JD Leiderdorp
The Netherlands
Child Usage Requirements
This stroller seat is suitable for use with children who meet the
following requirements:
Birth to 22 kg or 4 years whichever comes first.
When using the stroller frame with TRIV carry cot or Nuna infant
carriers, refer to the child usage requirements listed in those
instruction manuals.
Product Set Up
Open Stroller
1
- Take the stroller frame out. (1)
2
- Rotate the handle up to open the stroller frame. (2)
3
- Pull the seat to open it. (3)
A "click" sound means the seat is open.
Check that the stroller is completely latched open before
continuing.
Switch Seat
Please switch seat if you needed.
1
- Press the seat release button (4)-1 and lift the seat up (4)-2.
2
- Reverse the seat, and then attach it to the frame. (5)
A "click" sound means the seat is attached completely.
Front Wheels
1
- Insert the front wheel into the front leg. (6)
3
TRIV next instructions
A "click" sound means the front wheel is assembled
completely.
Check the wheel is securely attached by pulling out.Repeat
on opposite side.
2
- To remove the front wheel, press the release button (7)-1
and detach the front wheel from the front leg (7)-2.
Rear Wheels
1
- Insert the rear wheel into the rear leg. (8)
A "click" sound means the rear wheel is assembled
completely.
Check the wheel is securely attached by pulling out.Repeat
on opposite side.
2
- To remove the rear wheel, press the release button (9)-1
and detach the rear wheel from the rear leg (9)-2.
Arm Bar
Always secure the child with the harness. The arm bar is not
a restraint device.
1
- Align the arm bar ends with the arm bar mounts, and insert
until it clicks into place. (10)
A "click" sound means the arm bar is assembled completely.
2
- To remove the arm bar, press the arm bar release buttons
(11)-1 and remove the arm bar (11)-2.
Product Use
Securing Your Child
1
- Push the top button on the buckle (12)-1 to release the
buckle latch and remove the magnetic clips (12)-2. Place
your child in the stroller.
2
- Insert the magnetic clips into the buckle. (13)
3
- Fit the harness snugly to your child by pulling the
adjustment straps to tighten (14)-1. Then pull the waist
adjustment straps out (14)-2.
Shoulder Harness Position
1
- The upper shoulder harness buckles can be moved up and
down for added adjustment. (15)
To avoid serious injury from falling or sliding out, always
secure your child with the harness.
Make sure the harness is adjusted properly and your child
is snugly secured. The space between the child and the
shoulder harness should be about the thickness of one
finger.
DO NOT cross the shoulder belts. This will cause pressure
on child's neck.
Canopy
1
- To open the canopy, pull the canopy toward the front of
the seat, and to fold, push it back. (16)
2
- Open the zipper on the canopy for extra shade. (17)
3
- For added ventilation, flip the canopy window cover up.
(18)
Recline
There are 4 recline positions for the backrest.
1
- To raise or lower the backrest, squeeze the recline
adjustment button (19)-1, and pull the backrest up or down
(19)-2.
Please do not press the button (19)-3 on the middle of the
recline adjustment button when adjusting the angle for the
recline.
Make sure the recline is adjusted properly for use.
Calf Support
The calf support has 2 use positions.
1
- To raise the calf support, lift up.
2
- To lower the calf support, press the adjustment button
(20)-1, and push down (20)-2.
Handle
The handle has 5 positions.
1
- To adjust the height of the handle, pull the handle
adjustment button (21)-1 and pull the handle up or down
(21)-2.
Brake
1
To lock the rear wheels, step down on the brake lever. (22)
-
2
- To unlock the rear wheels, step down the brake lever again.
(23)
Always apply the brake when the stroller is stopped. Push
the stroller slightly to ensure the brake is engaged.
Front Swivel Locks
In Use Position:
It is recommended to use the front swivel locks on uneven
surfaces.
1
- Pull the front swivel lock up to lock the front wheel. (24)-1
Push the front swivel lock down to unlock. (25)
Fold Position:
Lock the wheels forward of the stroller frame before folding. This
allows the stroller to stand on its own.
2
- With the front wheel forward of the stroller frame, pull the
front swivel lock up (25)-1 to lock the wheel and push down
to unlock it. (25)-2
Fold
The stroller can be folded with forward facing seat or rear facing
seat or without the seat. Before folding the stroller, adjust the
handle to the lowest position and suggest the front swivel locks
are locked.
1
- Fold the canopy. (26)
2
- Press the folding release button (27)-1 on the middle of the
recline adjustment button and then squeeze the recline
adjustment button (27)-2.
3
- Fold the seat. (28)
4
- Pull the folding webbing of the seat to fold the stroller. (29)
5
- The stroller can stand by forward wheels swivel locked.
(30)
6
- Press the folding buttons of the seat mounts. (31)
7
- Fold the stroller. (32)
The stroller without seat can stand by handle and the front
wheels.
Insert
1
- To assemble the insert, place the insert over the seat and
thread the shoulder, waist and crotch harnesses through
their respective slots. (33)
Accessories
Not all accessories are included on some models.
Post adaptors
For Nuna infant carrier and TRIV carry cot assembly and usage,
please refer to the infant carrier and carry cot instruction manual.
1
- To attach the post adaptors, place the post adaptors on the
seat mounts. A "click" sound means the post adaptors are
attached. (34)(35)
2
- To attach infant carrier, place the infant carrier on the
post adaptors. A "click" sound means the infant carrier is
attached. (36)
3
- To attach carry cot, place the carry cot on the post
adaptors. A "click" sound means the carry cot is attached.
(37)
4
- The infant carrier and carry cot angle can be adjusted with
our adjustable adaptors. (38)
5
- When used with rear facing, the letters on the post
adaptors are the same as those on the frame plastic. (39)
6
- When used with front facing, the letters on the post
adaptors are opposite to those on the frame plastic. (40)
7
- To remove the infant carrier, push the release buttons on
the infant carrier (41)-1 and lift up (41)-2.
8
- To remove carry cot, press the release buttons on the side
of the carry cot (42)-1 and lift up (42)-2.
9
- To remove the post adaptors, pull the adaptor release
buttons (43)-1 and lift up (43)-2.
Remove the infant carrier and carry cot before folding.
Fold the Stroller with Post adaptors
Before folding the stroller with post adaptors, adjust the handle
to the lowest position and suggest the front swivel locks are
locked.
1
- Pull the folding webbing of the post adaptors to fold the
stroller. (44)
The stroller with the post adaptors can stand by handle and
the front wheels.
TRIV next instructions
4