Ayrton WILDSUN 200 S Mode D'emploi page 8

Menu
Set Dmx
Address A001~AXXX
Addr
Set Dmx Address A001~AXXX
Value Display PAN...
Set To Slave Slave1,Slave2,Slave3
Auto Program Master / Alone
Music Control Master / Alone
User Mode Stand Mode
Basic Mode
Extend Mode
User Mode A
User Mode B
User Mode C
Edit User Max channel
PAN :
Status Addr via DMX
No DMX Mode
Pan Reverse
Tilt Reverse
Pan Degree
Feedback
Pan/Tilt Spd
Zoom Speed
Mic Sens.
Hibernation
Service PIN Service PIN
RDM PID
Fans Control Head Control
Base Control
Disp.Setting Shutoff Time
Flip Display
Key Lock
DispFlash
Initial Pos. PAN =XXX
Trigger DMX Value Disp.
Set To Slave
Auto Program
Music Ctrl.
Reset Default ON/OFF
Time Info. Current Time
Ttl Life Hrs
Last Run Hrs
Timer PIN
Clr Last Run
Software Ver V1.0......
Home All
Pan&Tilt
Zoom
Test Channel PAN ......
Manual Ctrl. PAN =XXX
:
Calibration --Password--
PAN
:
Select Prog. Prog. Part 1 = Program 1 ~ 10 Program 1
Prog. Part 2 = Program 1 ~ 10 Program 2
Prog. Part 3 = Program 1 ~ 10 Program 3
Edit Prog. Program 1
:
Program 10
Edit Scenes Edit Scene 001
~ Edit Scene 128
Scenes Input XX~XX
All manuals and user guides at all-guides.com
DMX address setting
DMX address setting
DMX value display
Slave setting
Auto program
Music control
User's mode to change
channel numbers
Preset User modes
ON/OFF Add. via DMX
Close/Hold/Auto/Music Auto run if no DMX
ON/OFF Pan Reverse movement
ON/OFF Tilt Reverse movement
630/540 Pan Degree Select
ON/OFF Movement Feedback
switch
Speed 1~ 4 Movement Mode Select
Speed 1~ 2 Zoom Speed
0~99% Sensitivity of Mic.
OFF, 01M~99M,15M Standby mode
Password=XXX Service Code"=050"
xxxxxx RDM PID Code
75% Head Fans Speed Mode
High Select
Low
10% Base Fans Speed Mode
30% Select
50%
02~60m 05m Display shutoff time
ON/OFF Display Reverse 180
degree
ON/OFF Key Lock
ON/OFF Disp Flash if no DMX
Initial effect position
PAN...... DMX value display
Slave1,Slave2,Slave3 Slave setting
Master / Alone Auto program
Master / Alone Music control
Restore factory sett.
XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
Password=XXX
ON/OFF
Software version of each IC
Reset all motors
Reset Pan&Tilt
Reset Zoom
Test function
Fine adjustment of the lamp
Calbrate and adjust the
effects to standard/right
position Password "050"
Select programs to be run
Program Test Testing program
Step 01=SCxxx Program in loop
Step 64=SCxxx Save and exit
Pan,Tilt,...... Save and automatically
--Fade Time-- return
--Secne Time-- manual scenes edit
Input By Outside
Automat. scenes rec
Function mode
Set DMX Address
With this function, you can adjust the desired DMX-address via
the Control Board.
1. Access the main menu.
2. Tap the <Up/Down> button until "Set DMX Address" is
displayed.
3. Press ENTER, the display will show "Set DMX Address".
4. Tap the <Up/Down> button, the display will show
"A001~AXXX"
5. Press ENTER to confirm or press <MODE/ESC> to return
to the main menu.
Value Display
With this function you can display the DMX 512 value of each
channel. The display automatically shows the channel with a
value changing.
1. Access the main menu.
2. Tap the <Up/Down> button until "Value Display" is displayed.
3. Press ENTER, the display will show "Value Display".
4. Tap the <Up/Down> button, choose each channel.
5. Press ENTER to confirm or press <MODE/ESC> to return
to the main menu.
Set to slave
With this function, you can define the device as slave.
1. Access the main menu.
2. Tap the <Up/Down> button until "Set To Slave" is displayed.
3. Press ENTER, the display will show "Set To Slave".
4. Tap the <Up/Down> button, the display will show "Slave1",
"Slave2", "Slave3".
5. Press ENTER to confirm or press <MODE/ESC> to return
to the main menu.
Auto Program
With this function, you can run the internal program. You can
select the desired program under "Select program". You can
set the number of steps under "Edit program". You can edit the
individual scenes under "Edit scenes". With this function, you
can run the individual scenes either automatically, i.e. with the
adjusted Step-Time.
1. Access the main menu.
2. Tap the <Up/Down> button until "Auto Program" is
displayed.
3. Press ENTER, the display will show "Auto Program".
4. Tap the <Up/Down> button, the display will show "Master1",
" Alone".
5. Press ENTER to confirm or press <MODE/ESC> to return
to the main menu.
Music control
With this function, you can run the internal program sound-
controlled.
1. Access the main menu.
2. Tap the <Up/Down> button until "Music control" is displayed.
3. Press <ENTER>, the display will show "Music control".
4. Tap the <Up/Down>button, the display will show "Master1",
" Alone".
5. Press <ENTER> to confirm or press <MODE/ESC> to
USER MANUAL
8