Télécharger Imprimer la page

Worx HandyCut WX424 Traduction Des Instructions Initiales page 14

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 33
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
1. INSTALL /chANGE ThE bLADE
(See Fig. A)
wARNING: be sure to wear
protective work gloves while
handling a saw blade. The blade can
injure unprotected hands.
wARNING: This tool will be
extremely hot after use. be sure
to let saw, blade and blade spindle
clamping screw cool before changing
blades.
a. Unplug the saw.
wARNING: To prevent personal
injury, Always disconnect the plug
from power source before assembling
parts, making adjustments or changing
blades.
b. Loosen the blade spindle clamping screw
using the two hex keys included. Place
one key into the blade spindle clamping
14
14
screw and the other key into the back of the
spindle assembly. (See Fig. A)
c. Turn the key that is in the clamping screw
clockwise while holding the other key
stationary.
d. Remove the screw and the blade clamping
washer. (See Fig. B, C)
e. Set the depth of cut scale to the maximum
depth of 22 mm. Release the blade release
lever and rasie the base with the finger
lift bracket to expose the blade below the
base.
f. Grasp the blade with your gloved hand
and remove the blade, or install the blade,
through the blade slot in the base.
g. Place the new saw blade through the blade
slot in the base and onto the spindle shaft.
NOTE: The teeth of the blade should
point upward at the front of the saw as
shown in (See Fig. b).
NOTE: The warning copy and the blade
Rotation Arrow shown on the blade should
face outward towards the operator so it can
be viewed (See Fig. c).
Mini multi-function saw
All manuals and user guides at all-guides.com
h. Replace the blade clamping washer .
i. Replace the spindle screw and hand tighten
j. Use the two hex keys to tighten the spindle
k. Place the two hex keys back in the case.
NOTE: Never use a blade that is too thick to
allow the blade clamping washer to engage
with the flat side of the spindle.
2. MAKING DEPTh OF cUT
ADjUSTMENTS (See Fig. D)
NOTE: Always use the correct blade depth
setting. The correct blade depth setting for all
cuts should not be more than 6 mm below the
material being cut. Allowing more depth will
increase the chance of kickback and cause the
cut to be rough. Your saw is equipped with
a depth of cut scale that provides increased
depth of cut accuracy. The depth of cut scale
is located on the top of the upper blade guard
(See Fig. D).
Our suggest cut depth:
Wood
Alu
PVC pipe
Tile
TO SET ThE bLADE DEPTh (Fig. E1, E2)
Determine the desired depth of cut. Unlock
the depth of cut and length of cut Indicator
adjustment/Lock lever. Slide the depth of cut
indicator to the desired depth of cut. Lock
down the depth of cut adjustment / lock lever.
The length of cut indicator (See Fig.D) is ideal
for plunge or pocket cutting into the middle
(or interior) of the work piece when you need
to know where the cut will begin and where
it will end. This feature allows you to pinpoint
the location where the blade will plunge into
the work piece, based on the blade depth that
was selected. Always practice in a scrap work
piece to become familiar with this cutting
operation. The selected depth of cut is now
set. When the saw's blade is manually lowered
(See Fig. Ka, Kb), the blade will be below the
base at the selected depth.
it in a counterclockwise direction.
clamping screw thoroughly.
Max. cut depth
0-22 mm
0-3 mm
0-12 mm
0-8 mm
EN

Publicité

loading