Publicité
Les langues disponibles
Les langues disponibles
PROGRAMMING THE WEEKLY TIMER
with the same setting for all days of the week.
Setting on/off, temperature/humidity.
Press MENU – Use the left and right arrow keys (
settings. Start programming mode using the down arrow (
Select the setting number (for example, setting 1) using the left and right
Õ Ö
arrow keys (
). Shift to programming mode by pressing the down arrow
Ø
(
)
Select the starting time (hour) by using the up and down arrows (
shift to minutes with the right arrow (
× Ø
up and down arrows (
).
Select the termination time by using the right arrow (
× Ø
arrows to set the end hour(
), then shift to minutes with the right arrow
Ö
(
). Change the end minutes using the up and down arrows (
Shift to temperature settings with the right arrow (
temperature using the up and down arrows (
Ö
the right arrow (
). Change the humidity using the up and down arrows
× Ø
(
). Shift to on/off with the right arrow (
× Ø
the up and down arrows (
).
Now the setting (1) has been programmed; press MENU to return to
programming mode. Programme each setting using the left and right arrow
Õ Ö
keys (
). The Tylarium can be programmed to switch on and off for a
maximum of four times a day. When all settings are done, go back to timer
settings by pressing MENU twice, press ON, and the weekly settings are
activated. A red LED flashes until the Tylarium starts at a set time; after this it
glows steadily (a message on the display will appear when this happens).
To switch the Tylarium off manually, press OFF. (This only switches off the
current bath).
If the humidity exceeds 30% when the unit is switched off, a dehumidifier
switches on automatically and runs for approximately 20 minutes.
To de-activate the programming of the weekly settings, press MENU, use the
Õ Ö
left and right arrows (
) to shift to timer settings and press OFF.
STAND-BY PROGRAMMING
with different settings for different days of the week.
Press MENU – Use the left and right arrow keys (
settings. Start programming mode using the down arrow (
Õ Ö
Use the left and right arrow keys (
Shift to programming mode by pressing the down arrow (
Select the starting time (hour) by using the up and down arrows ,(
shift to minutes with the right arrow (
× Ø
up and down arrows (
).
Select the termination time (hour) by using the up and down arrows (
then shift to minutes with the right arrow (
× Ø
the up and down arrows (
).
Shift to temperature settings with the right arrow (
temperature using the up and down arrows (
Ö
the right arrow (
). Change the humidity using the up and down arrows
× Ø
(
). Shift to on/off with the right arrow (
× Ø
the up and down arrows (
).
Now the stand-by setting (Monday) has been programmed; press MENU to
return to programming mode. Programme the stand-by times for each day.
When all settings are done, go back to stand-by settings in the MENU
programme, press ON, and the weekly settings are activated. A red LED
flashes until the Tylarium starts at the pre-set time; after this it glows steadily
(a message on the display shows that the panel is in stand-by mode and
when it will switch on).
As soon as you press ON, the temperature increases to the pre-set bathing
temperature. After 1 hour, the unit resumes the stand-by temperature. Each
time the ON button is pressed, a new 1-hour bathing period starts.
Note: If the timer timing and stand-by timing are set to be on concurrently, the
timer function will take precedence.
To switch off manually, press OFF. (This only switches off the current bath).
To de-activate the programming of the stand-by settings, press MENU, use
the left and right arrows to shift to timer settings and press OFF.
To restart with the same settings, press MENU, go to stand-by using the left
Õ Ö
and right arrows (
), and press ON.
NOTE: Always use the code lock function in connection with stand-by
programming.
STAND-BY PROGRAMMING
with the same setting for all days of the week.
Press MENU – Use the left and right arrow keys (
settings. Start programming mode using the down arrow (
Õ Ö
Use the left and right arrow keys (
programming by pressing the down arrow (
Select the starting time (hour) by using the up and down arrows (
shift to minutes with the right arrow (
× Ø
up and down arrows (
).
All manuals and user guides at all-guides.com
Õ Ö
) to select the timer
Ø
).
× Ø
), then
Ö
). Change the start minutes using the
Ö
), use the up and down
× Ø
).
Ö
). Change the
× Ø
). Shift to RH% settings with
Ö
). Change the on/off mode using
Õ Ö
) to go to stand-by
Ø
).
) to set the day (for example, Monday).
Ø
).
× Ø
), then
Ö
). Change the start minutes using the
× Ø
Ö
). Change the end minutes using
Ö
). Change the
× Ø
). Shift to RH% settings with
Ö
). Change the on/off mode using
Õ Ö
) to go to stand-by
Ø
).
) to select the mode WEEK. Shift to
Ø
).
× Ø
), then
Ö
). Change the start minutes using the
Select the termination time by using the right arrow (
× Ø
arrows (
) to set the end hour, then shift to minutes with the right arrow
Ö
(
). Change the end minutes using the up and down arrows (
Shift to temperature settings with the right arrow (
temperature using the up and down arrows (
Ö
the right arrow (
). Change the humidity using the up and down arrows
× Ø
(
). Shift to on/off with the right arrow (
the up and down arrows (
Now the stand-by time has been programmed. Go back to stand-by
programming by pressing MENU twice, press ON. A red LED flashes until the
Tylarium starts at the pre-set time; then it glows steadily (a message on the
display shows that the panel is in stand-by mode and when it will switch on).
As soon as you press ON, the temperature increases to the pre-set bathing
temperature. After 1 hour, the facility automatically resumes stand-by
temperature. Each time you press ON, 1 hour's bathing time is begun.
Note: If the timer timing and stand-by timing are set to be on concurrently, the
timer function will take precedence.
To switch off manually, press OFF. (This only switches off the current bath).
To de-activate the programming of the stand-by settings, press MENU, use
the left and right arrows (
To restart with the same settings, press MENU, go to stand-by using the left
Õ Ö
and right arrows (
), and press ON.
NOTE: Always use the code lock function in connection with Stand-by
programming.
CODE LOCK.
Setting the code lock.
Press MENU – Use the right and left arrows (
Start programming mode by pressing the down arrow (
Õ Ö Ø ×
keys (
) to enter the code. After a power failure, the code is reset to
1995. Press MENU, use the left arrow key (
new code using the arrow keys (
Ö
the right arrow (
), press MENU. Now the code lock is activated.
To return to a mode of operation without a code lock, repeat the above
procedure but set on/off to off.
Note: Program all other settings before setting the code lock.
BATHING OUTSIDE OF THE PROGRAMMED SCHEDULE
if the panel lock is activated.
The Tylarium can be used at other times than pre-programmed. Press ON to
start a one-hour bathing period. To extend the bath, press ON again. The unit
automatically switches off one hour after ON was pressed last.
),
The Tylarium offers sauna bathing in all its forms: dry sauna, wet sauna and
steam baths. Since the relative humidity sometimes is higher than in a
traditional sauna bath, please observe the following recommendations.
• If the sauna has a window in the door or wall, treat the entire lower
moulding with boat varnish and seal the joint between the glass and the
moulding with a water-resistant silicone sealant. This prevents any
condensation on the glass from seeping into the joint.
• Varnish the threshold and door handles a few times with boat varnish to
maintain the finish and simplify cleaning the sauna. Benches, decorative
edging and back supports should be oiled on both sides with Tylö sauna
oil.
Note: All other wood in the sauna should be left untreated.
TYLÖ AB, Svarvaregatan 6, S-30250 Halmstad, Sweden.
Phone 035-10 00 80, Fax 035-102580.
© This publication may not be reproduced, in part or in whole, without the written permission of Tylö. Tylö
reserves the right to make changes in materials, construction and design.
Ö
), use the up and down
Ö
). Change the
× Ø
). Shift to RH% settings with
Ö
). Change the on/off mode using
× Ø
).
Õ Ö
) to shift to stand-by setting and press OFF.
Õ Ö
) to go to code lock setting.
Ø
). Use the arrow
Õ
) to change the code. Set the
Õ Ö Ø ×
). Press MENU. Activate on/off with
TYLARIUM
× Ø
).
9
Publicité
