Publicité
Les langues disponibles
Les langues disponibles
SETTINGS
Note: CC 200–3/12 only
Note: Program all settings in the OFF position.
However, temperature and humidity settings may also be changed in
the ON position.
MANUAL ON/OFF.
Setting the bathing temperature.
Press TEMP – the previous temperature setting is displayed. Use the up and
× Ø
down arrows (
) to change the temperature.
Setting relative humidity RH%.
Press RH % – the previous setting is displayed. Use the up and down arrows
× Ø
(
) to change the humidity (max 65%).
Note: The electronic control logics will limit the maximum humidity at given
temperatures.
Manual on/off.
Press ON to switch the unit on. Press OFF to switch it off. If you forget to
switch it off manually, the unit automatically switches off after 3 or 12 hours –
depending on the type of control panel.
If the humidity exceeds 30% when the unit is switched off, a dehumidifier
switches on automatically and runs for approximately 20 minutes.
AUTOMATIC ON/OFF.
Setting on/off and temperature/humidity.
Press MENU – Use the left and right arrow keys (
Ø
settings. Use the down arrow (
) to start programming mode.
Select the starting time (hour) by using the up and down arrows (
shift to minutes with the right arrow (
× Ø
up and down arrows (
).
Select the termination time by using the right arrow (
× Ø
(
) arrows to set the end hour, then shift to minutes with the right arrow
Ö
(
). Change the end minutes using the up and down arrows (
temperature settings with the right arrow (
× Ø
the up and down arrows (
). Shift to RH% setting with the right arrow (
Change the humidity using the up and down arrows (
Ö
the right arrow (
). Change the on/off mode using the up and down arrows
× Ø
(
).
Now the setting is programmed and a red LED flashes until the Tylarium
starts at the time set. After this, it glows steadily (a message on the display
shows when this happens).
You can switch off the Tylarium manually at any time by pressing OFF. To
restart with the same settings, press MENU – Use the right and left arrows (
Ö
) to go to timer settings. Start programming mode by pressing the down
Ø
arrow (
), shift to on/off with the right arrow (
× Ø
using the up and down arrows (
If the humidity exceeds 30% when the unit is switched off, a dehumidifier
switches on automatically and runs for approximately 20 minutes.
STAND-BY.
Stand-by programming.
Press MENU – Use the right and left arrows (
Start programming mode by pressing the down arrow (
Select the starting time (hour) by using the up and down arrows (
shift to minutes with the right arrow (
× Ø
up and down arrows (
).
Select the termination time by using the right arrow (
× Ø
down arrows (
) to change the end hour, then shift to minutes with the
Ö
right arrow (
). Change the end minutes using the up and down arrows
×Ø
(
).
Shift to temperature settings with the right arrow (
temperature using the up and down arrows (
Ö
the right arrow (
). Change the humidity using the up and down arrows (
Ö
Shift to on/off with the right arrow (
× Ø
and down arrows (
).
Now the stand-by is programmed and a red LED flashes until the Tylarium
starts at the time set. After this the LED glows steadily (a message on the
display shows that the panel is in a stand-by mode and when it will switch on).
Note: If the timer timing and stand-by timing are set to be on concurrently, the
timer function will take precedence.
You can switch off the Tylarium manually at any time by pressing OFF. To
restart with the same settings, press MENU – Use the right and left arrows (
Ö
) to go to stand-by settings. Start programming mode by pressing the down
Ø
arrow (
), shift to on/off with the right arrow (
× Ø
using the up and down arrows (
8
All manuals and user guides at all-guides.com
Õ Ö
) to move to timer
× Ø
), then
Ö
). Change the start minutes using the
Ö
), use the up and down
× Ø
). Shift to
Ö
). Change the temperature using
× Ø
). Shift to on/off with
Ö
). Change the on/off mode
).
Õ Ö
) to go to stand-by settings.
Ø
).
× Ø
), then
Ö
). Change the start minutes using the
Ö
), then use the up and
Ö
). Change the
× Ø
). Shift to RH% settings with
). Change the on/off mode using the up
Ö
). Change the on/off mode
).
CODE LOCK
.
Setting the code lock.
Press MENU – Use the right and left arrows (
settings. Start programming mode by pressing the down arrow (
code using all the arrow keys (
reset to 1995. Press MENU, use the left arrow key (
Set the new code using all the arrow keys (
on/off with the right arrow (
To return to a mode of operation without a code lock, repeat the above
procedure but set on/off to off.
Note: Program all other settings before setting the code lock.
Note: Program all settings in the OFF position.
However, temperature and humidity settings may also be changed in
the ON position.
MANUAL ON/OFF.
Setting the bathing temperature.
Press TEMP – the previous temperature setting is displayed. Use the up and
× Ø
down arrows (
) to change the temperature.
Setting relative humidity RH%.
Press RH% – the previous setting is displayed. Use the up and down arrows
× Ø
(
) to change the humidity (max 65%).
Note: The electronic control logics will limit the maximum humidity at given
temperatures.
Manual on/off.
Important! Don't forget to set the end time. The Tylarium may be in
continous operation for a maximum of 12 hours.
Press ON to switch the unit on. Press OFF to switch it off.
Ö
If the humidity exceeds 30% when the unit is switched off, a dehumidifier
).
switches on automatically and runs for approximately 20 minutes.
PROGRAMMING THE WEEKLY TIMER
with different settings for different days of the week.
Setting on/off, temperature/humidity.
Press MENU – Use the left and right arrow keys (
settings. Start programming mode using the down arrow (
Use the left and right arrow keys (
Õ
Shift to programming mode by pressing the down arrow (
Choose the setting number (such as setting 1) with the left and right arrow
Õ Ö
keys (
). Shift to programming mode by pressing the down arrow (
Select he starting time (hour) by using the up and down arrows (
shift to minutes with the right arrow (
× Ø
up and down arrows (
Select the termination time by using the right arrow (
arrows to set the end hour (
Ö
(
). Change the end minutes using the up and down arrows (
Shift to temperature settings with the right arrow (
temperature using the up and down arrows (
Ö
the right arrow (
). Change the humidity using the up and down arrows (
Shift to on/off with the right arrow (
× Ø
and down arrows (
).
Now the setting (Monday, setting 1) has been programmed; press MENU to
return to programming mode. Programme the start and stop time for each
day by moving to the day/setting with the left and right arrow keys (
Tylarium can be programmed to switch on and off for a maximum of four
times a day. When all settings are done, go back to timer settings by
×Ø
pressing MENU twice, press ON, and the weekly settings are activated. A red
).
LED flashes until the Tylarium starts at a set time; after this it glows steadily
(a message on the display shows when this happens).
As soon as you press ON, the temperature increases to the pre-set bathing
temperature. After 1 hour, the unit automatically resumes stand-by
temperature. Each time you press ON, 1 hour's bathing time is begun.
To switch off manually, press OFF. (This only switches off the current bath).
If the humidity exceeds 30% when the unit is switched off, a dehumidifier
switches on automatically and runs for approximately 20 minutes.
Õ
To de-activate the programming of the weekly settings, press MENU, use the
Õ Ö
left and right arrows (
Õ Ö
) to go to code lock
Õ Ö Ø ×
). After a power failure, the code is
Õ
) to change the code.
Õ Ö Ø ×
). Press MENU. Activate
Ö
), press MENU. Now the code lock is activated.
SETTINGS
Note: CC 200–0 only.
Õ Ö
) to select the timer
Ø
Õ Ö
) to set the day (for example, Monday).
Ø
).
Ö
). Change the start minutes using the
).
Ö
), use the up and down
× Ø
), then shift to minutes with the right arrow
Ö
). Change the
× Ø
). Shift to RH% settings with
Ö
). Change the on/off mode using the up
) to shift to timer settings and press OFF.
Ø
). Enter the
).
Ø
).
× Ø
), then
× Ø
).
×Ø
).
Õ Ö
). The
Publicité
