Peg-Perego Aria Notice D'emploi page 13

STROLLER ASSEMBLY
3• Take care to mount the two wheels fitted
with brakes on the rear of the stroller. Fit
the wheel, push button A while pushing
the wheel further until you hear the final
click: the wheel is securely fastened.
4• To mount the front wheels, push down
lever A, then slide on the wheel till it
clicks.
5• Attach the front bar as shown in the
fi gure.
HOOD
6• To attach the hood, insert the tabs into
the special notches.
7• Fasten the hood to the back of the
backrest, and press down on the side
braces as shown in the figure.
8• To remove the hood, press the side
buttons while lifting the hood off, as
shown in the figure.
DRINK-HOLDER
The drink-holder attaches to the right
side of the handlebar only.
9• To attach the drink-holder to the
handlebar, open the band and fasten it as
shown in the figure. Slip the drink-holder
into the band, and click into place.
10• Insert the two caps, as shown in the
figure, taking care to line them up
correctly. Use two coins to turn the caps
that fasten the drink-holders, as shown
in the figure.
Do not place hot drinks in the drink-
holder. Do not place anything heavier
than 0,5 Kg (1 lbs.) in the drink-holder.
BRAKE
11• To brake the stroller, push the levers on
the rear wheels downwards with your
foot. To release the brakes, lift the levers.
Always set the brake when the stroller is
not moving.
SAFETY BELT
12• A: Make sure that the brace is properly
inserted by pushing as shown in the
figure. B: Fasten the belt as shown in the
figure.
13• To unfasten the belt, press on the buckle
sides and pull out the waist strap.
14• The new safety belt is now easier to
fasten thanks to the "snap-open-and-
shut" device. Before fastening the safety
belt, attach the buckle to the backrest
by inserting the tab through the special
holder, as shown in the figure. After
fastening the safety belt on your child,
detach it from the backrest to allow the
child more freedom of movement. The
buckle must remain below the child's
shoulders.
ADJUSTING THE BACKREST
15• To recline the backrest, lower the
All manuals and user guides at all-guides.com
16• To raise the backrest, push the backrest
17• Lower the lever as shown in the figure to
18• The front bar-child tray can be opened
19• To remove the front bar-child tray, press
20• If it is necessary to replace the basket,
21• Fasten the back of the basket, closing the
22• To remove the front wheels, set them
23• To remove the rear wheels, press the
24• To fold up the stroller, lift the buttons
25• Push the backrest and the hood towards
26• The stroller can easily be carried by the
27• To remove the lining from the stroller,
28• then outwards. Slip the pin out of the
backrest adjuster button while pushing
the backrest down.
adjuster button upwards, as shown in the
fi gure.
SWIVELING WHEELS
allow the front wheels to swivel. Lift the
lever for fixed wheels.
FRONT BAR-CHILD TRAY
only from one side, to allow the child to
climb in and out of the stroller when he
or she is old enough. To open, press the
button with one hand, while using the
other hand to swing the tray upwards.
the two buttons as shown in the figure
while pulling the tray upwards. Do not
place boiling-hot drinks on the child tray;
this could be dangerous.
REPLACING THE BASKET
fasten the front of the new basket to the
hooks as shown in the figure.
buttons as shown in the figure.
REMOVING THE WHEELS
The wheels on the stroller are removable.
to swivel, press the levers and push the
wheel until it comes off , as shown in the
fi gure.
button and push the wheel downward
until it comes off , as shown in the fi gure.
FOLDING UP THE STROLLER
Before folding up the stroller, pull the
side braces upwards if the hood is
attached.
on the sides of the handlebar and swing
the handlebar forwards until it clicks into
place.
the stroller, while lowering the handlebar
into its housing. Check to make sure that
the stroller is fastened securely with the
safety hook. The folded-up stroller will
stand upright by itself.
TRANSPORT
handle when it is closed.
REMOVABLE LINING
remove the little cover on the side by
pressing on it. Push the pin upwards and
hole in the sack. Repeat on the other side.