Scheppach ksm 2000 Traduction Du Manuel D'origine page 10

workpiece with the table or the fence. Exceptions are
the sanding of curved workpieces on the outside of the
sanding disc.
• Always clear the table, fence or sanding belt of scraps
or other objects, before turning the machine on.
• Do not perform any layout assembly or set-up work on
the table while the sanding machine is in operation.
• Switch the machine off and pull the power plug from
the socket when fitting or removing accessories.
• Never leave the working area of the sanding machine
while the tool is running, or as long as it has not come
to an absolute standstill.
m Proper Use
The machine meets the currently valid EU machine direc-
tive.
• The safety, working, and maintenance instructions and
the dimensions set forth in the specifications must be
observed.
• The applicable regulations for the prevention of acci-
dents and other, generally recognized safety rules must
be observed.
• The machine may only be used, maintained or repaired
by trained persons who are familiar with the machine
and have been informed about the dangers. Unauthor-
ized modifications of the machine exclude a liability
of the manufacturer for damages resulting from the
modifications.
• The machine may only be used with original accessories
and original tools of the manufacturer.
• Any other use is considered to be not intended. The
manufacturer excludes any liability for resulting dam-
ages, the risk is exclusively borne by the user.
m Residual Risks
The machine has been constructed according to the state
of the art and the recognized safety rules. Nevertheless,
single residual risks may occur during the operation.
• Risk of injuries for fingers and hands caused by the ro-
tating grinding roller in the case of an improper guid-
ance or support of the work piece to be ground.
• Risk of injury caused by hurling work pieces in case of
an improper support or guidance.
• Danger caused by electric current if inappropriate elec-
trical connecting lines are used.
• Furthermore, non obvious residual risks may exist in
spite of all measures taken.
• Residual risks can be minimized by carefully observing
the Safety Notes and the Intended Use as well as the
entire operating instructions.
All manuals and user guides at all-guides.com
1
2
3
4
5
6
7
8
9
10 Cross cutting gauge
11 Table clamping
12 Shifting knob
13 Belt clamping bracket
14 Adjustment handle
For logistical reasons, your machine is not completely as-
sembled.
We recommend attaching the machine to the base frame
with which it that is delivered.
Four screws are included for this purpose.
Lengthwise table with adjustable clamp, fig. 3
1 Screw the lengthwise table with the 2 locking handles
2 Place the adjustable clamp through the lengthwise ad-
Assembling the lateral table, fig. 4
1 Mount the lateral table on the frame with 4 hex bolts, 4
2 Set the scale index to 90°.
Assembling the sanding stop collar, fig. 5
Mount the sanding stop collar with 2 socket screws on
the frame.
Mounting the suction hood, fig. 6
Mount the suction hood on the sanding table with a
round-head screw, washer and wing nut (A).
Mounting the switch, fig. 6
Attach the switch with 2 screws to the switch plate (B).
Mounting the sanding belt, fig. 7
1 The clamping lever allows the sanding belt to be tight-
2 To put the sanding band in place, the clamping lever
3 Loosen the handles, so that the pinch pin is loos-
4 Lift up the protective shield (4) and place the sanding
5 To tighten the sanding belt, turn the clamping lever in
6 Put the protective shield back in place and tighten the
Equipment Fig. 1–2
Base (packed separately)
Sanding frame
Traverse table
Lateral table
Motor
On/Off switch
Extraction nozzle
Sanding belt
Sanding stop plate
Assembly
loosely.
justment plane in the housing and secure it with the
2 spring pins. Adjust the table and the scale index to
90°.
washers, 4 hex nuts and tighten it slightly by hand. Align
the lengthwise table into the corner and tighten.
ened or loosened.
must point in the direction of the arrow (1).
ened.
belt on the rollers. Pay attention to the arrows indicating
the direction on the inner side of the sanding belt.
the direction of the arrow (2).
handles (3).
english 11