Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Technical data for Jøtul I 400 FL according to EN 13229
Nominal heat output:
Flue gas mass flow:
Recommended chimney draught:
Efficiency:
CO emission (13% O
):
2
Flue gas temperature:
Operational type:
Technical data for Jøtul I 500 FL according to EN 13229
Nominal heat output:
Flue gas mass flow:
Recommended chimney draught:
Efficiency:
CO emission (13% O
):
2
Flue gas temperature:
Operational type:
Technical data for Jøtul I 530 FL according to EN 13229
Nominal heat output:
Flue gas mass flow:
Recommended chimney draught:
Efficiency:
CO emission (13% O
):
2
Flue gas temperature:
Operational type:
3.0 Safety
NB! To guarantee optimal performance and safety, Jøtul stoves
must be fitted by a qualified installer.
Any modifications to the product by the distributor, installer
or consumer may result in the product and safety features not
functioning as intended. The same applies to the installation of
accessories or optional extras not supplied by Jøtul. This may
also be the case if parts that are essential to the functioning
and safety of the fireplace have been disassembled or removed.
In all these cases, the manufacturer is not responsible or liable
for the product and the right to make a complaint becomes null
and void.
3.1 Fire Prevention Measures
There is a certain element of danger every time you use your
fireplace. The following instructions must therefore be followed:
•
The minimum safety distances when installing and using the
fireplace are given in fig. 1.
•
Ensure that furniture and other flammable materials are not
too close to the fireplace. Flammable materials should not be
placed within 1 metre of the fireplace.
•
Allow the fire to burn out. Never extinguish the flames with
water.
•
The fireplace becomes hot when lit and may cause burns if
touched.
•
Only remove ash when the fireplace is cold. Ash can contain
hot embers and should therefore be placed in a non-
flammable container.
•
Ash should be placed outdoors or be emptied in a place where
it will not present a potential fire hazard.
6
In case of chimney fire:
6,0 kW
•
Close all hatches and vents.
7,3 g/s
•
Keep the firebox door closed.
12 Pa
•
Check the loft and cellar for smoke.
74 %@6,0 kW
•
Call the fire service.
0,19%
•
Before use after a fire an expert must check the fireplace
o
259
C
and the chimney in order to ensure that it is fully functional.
Intermittent
3.2 Foundations
9,0 kW
You need to make sure the foundation is suitable for a stove. See
8,1 g/s
"2.0 Technical data" for specified weight.
12 Pa
80%@ 9,9 kW
Remember: If a steel chimney resting on the burn chamber is
0,06 %
being used, the weight of the steel chimney should be taken
o
314
C
into account.
Intermittent
NB: It is extremely important that the product be stable; the
surface it is installed on must be completely inflexible.
9,0 kW
It is recommended that flooring that is not attached to the
8,4 g/s
foundation – «floating floors» – be removed beneath the product.
12 Pa
71%@ 9,0 kW
3.3 Floor covering
0,25 %
o
350
C
Jøtul Cube has an airtight bottom plate and no extra floor
Intermittent
covering is required beneath the product.
Any floor covering of inflammable material, such as linoleum,
carpets, etc. must be removed from under the product.
3.4 Floor plate
A plate made of steel or some other suitable non-inflammable
metal (optional extra) is placed in front of the hearth.
The floor plate must comply with national laws and regulations.
Contact your local building authorities regarding restrictions and
installation requirements..
3.5 Air supply
There must be a flow of air between the burn chamber and the
surround. This is to ensure that there is not too great a build-up
of heat inside the surround.
NB: It is extremely important that air openings not are covered
up. See Fig. 1a and Fig. 1b for distances.
Publicité
Chapitres
