Storage Of The Boat; Treatment And Storage; Guarantee Conditions; Boat Repairs - Gumotex THAYA Manuel De L'utilisateur

Masquer les pouces Voir aussi pour THAYA:

Manuel de l'utilisateur (44 pages)

Les langues disponibles

5. storage of the boat – see Picture 4

Open the valves and release the air from all the chambers.

Deflate the seats and the front foot-rest. Open the valves and

release the air from the main chambers.

The kayak can be deflated more quickly by rolling it in the di-

rection of the valves. No sharp objects should remain in the

kayak. When deflated, lay out the kayak in such manner that

the bottom lies on the ground and the sidewall cylinders are

folded inwards. Then fold both sidewall cylinders to thirds over

the bottom of the kayak and then fold the kayak from the bow

towards the valves. Insert the folder kayak into the transporta-

tion bag. Expel the air from the bag, roll up the insertion end

and fasten it with clips.

6. treatment and storage

The rubber surface coating of the boat is sensitive to oils, gas-

oline, toluene, acetone, kerosene and similar thinning agents.

Prior to storing a dirty boat, wash it down with warm soapy

water. Rinse the boat with fresh water after using the boat in

seawater. It is recommended to check the state of the inflation

valves and the safety relief valves. If a valve is not airtight, it is

possible to unscrew the valve body from the boat with the use

of a special valve-key and clean its membrane with a strong jet

of water or compressed air. Prior to storage, it is recommend-

ed to rub the surface of the canoe with an agent intended for

the treatment of such surfaces, which has cleaning properties,

and which impregnates the material to prevent further dirtying,

or which is capable of forming a protective UV-filter. Never use

agents containing silicon when treating your boat. Store the

clean and dry product in a dark dry place at a temperature

of (15 – 35) °C, at least 1.5 m from any radiant heat source

and out of the reach of rodents. During longterm storage, it

is recommended to inflate the boat for 24 hours from time to

time to avoid fatiguing the fold lines. It is also recommended

to have the boat serviced by the manufacturer's authorized

service station at least once every two or three years.

Proper care and treatment of the boat will increase its

service life.

7. Guarantee Conditions

The guarantee period is 24 months and is calculated from the

date of sale.

The producer provides cost-free repairs or replacement of

faulty components for material faults or production faults.

The warranty does not cover damage to air chambers due

to higher pressure than the required operational pres-

sure!!!

8. boat Repairs

You can easily repair a damaged boat yourselves by means of

the accompanying gluing set.

Gluing:

mark out the damaged area on the boat and choose an

appropriately sized patch;

the surfaces of both patch and place to be glued must be

clean, dry and without traces of old glue;

we recommend degreasing both surfaces with acetone in

order to achieve a perfect bond;

spread a thin layer of glue on both surfaces to be glued

and repeat this step once the first layer has dried;

after the second layer has dried, press the patch firmly on

the damaged place, weigh down or use a rolling pin on

a flat surface.

For minor repairs (punctures), it is possible to re-inflate the

boat and continue using it after waiting for approx. 30 minutes;

after more serious repairs, you should wait for 24 hours before

using the repaired boat. Complicated repairs should be per-

formed by the manufacturer or at authorized service stations.

Guarantee repairs and post-guarantee repairs are pro-

vided by the manufacturer:

GUMOTEX Coating, s.r.o.

Mládežnická 3062/3a

690 02 Břeclav

Czech Republic

9. Product Disposal Method

The product should be disposed of at municipal waste dis-

posal sites.

10. Packaging Disposal Method

Cardboard – recycle as the indicated symbol directs.

PE bubble foil – recycle as the indicated symbol directs.

11. Manufacturer's label

– legend of symbols used

Each boat is provided with its own Type Parameters Tag which

displays the most important technical parameters. Please

follow these values. Above all, do not overload the boat and

maintain the recommended maximum pressures in the air

chambers.

GUMOTEX Coating, s.r.o., Mládežnická 3062/3a, 690 02 Břeclav, CZ

Explanation of the symbols used:

maximum operational pressure

maximum number of people

maximum load

Table des Matières