Elkron DC6002I/BR Guide Rapide page 4

Test mode
Whenever the Test button is pressed, the contact transmits a signal to the control unit to test the radio range and

activates Test mode for three minutes.
The LED lights up whenever the contact is activated during the Test.

Test mode is extended by three more minutes if the Test button is pressed again.

Preparation
Remove the insulation of the battery.

Activate the learn function on the control unit.

By means of the learn function, pair the internal/tamper magnetic switch and the wired inputs to an input of the control

unit.
Press the test button for the learning of the device.
If the signal is received from the control unit it will show the corresponding information. Refer to the control unit manual

to complete the learning procedure.
Once the contact learning procedure has been run, set the control unit to "Walk Test" mode, holding the contact in the

required position and press the Test button to confirm that the chosen position is within the radio range of the control
unit.
Proceed with the installation after having ascertained that the contact is working in the desired

Mounting and installation methods
The contact must be positioned on the door frame while the magnet must be positioned on the
door. If the contact is positioned on the door and the door is opening too fast, the transmission
distance may be reduced.
The magnet must not be more than 15 mm from the contact when the door is closed.
< < N N O O T T E E > >

If the contact cannot be installed on the door frame, additional opening detectors
can be used on the wired inputs (see the "How to use the terminals" section for
details).
Step 1: Identify an appropriate position near the door/window where the contact is positioned.
Step 2: The contact has two rib-marks on one side which indicate the position of the magnet.
The contact may be installed straight or upside down to ensure that the rib-marks are
aligned with the magnet.
Step 3: To fit the contact:
(i) Using the two mounting holes of the contact as a template, mark the position of the holes in the more suitable
position.
(ii) Insert the anchor bolts if the device is fixed to plaster or bricks.
(iii) Screw the contact onto the anchor bolts.
Step 4: Position the magnet on the door using the two-sided adhesive or the screws provided. The magnet must be
aligned with the side rib-marks of the contact as shown in the
< < N N O O T T E E > >

Make sure that the spring of the tamper switch makes contact against the resting surface passing through the
opening of the tamper switch.
Step 5: Test the contact by opening and closing door or window with the control unit in "Walk test" mode.
Step 6: Insert the white plugs in the two mounting holes of the contact.
Step 7: The installation is complete.
Radio frequency of use: 868,6 - 868,7 MHz
Radio power transmitted: 1,81 dBm
Hereby, URMET S.p.A. declares that the radio equipment type: WHITE/BROWN MAGNETIC CONTACTS WITH WIRED INPUTS
DC6002I is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: www.elkron.com.
CLICK ON THE FOLLOWING LINK OF THE ELKRON SITE TO ACCESS THE PRODUCT TECHNICAL SHEET
AND DOWNLOAD THE COMPLETE MANUAL:
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste
electrical and electronic equipment (WEEE).
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the environment. For more information
about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
ELKRON
Tel. +39 011.3986711 - Fax +39 011.3986703
www.elkron.com
SIMPLIFIED EU DECLARATION OF CONFORMITY
– mail to: info@elkron.it
figure.
ELKRON is a trademark of URMET S.p.A.
Via Bologna 188/C – 10154 Turin (TO) Italy
www.urmet.com
position.
MADE IN TAIWAN