Cleaning And Maintenance - Royal Catering RCPS-16EB Manuel D'utilisation

AREA OF APPLICATION
The popcorn maker is designed to make popcorn.
Any damage resulting from a non-conform use of the device is the responsibility of
the user!
TECHNICAL DETAILS
Product name
Model
Voltage (V)
Power (kW)
Frequency (Hz)
Temperature (°C)
Amount of oil (ml/once)*
Amount of sugar (g/once)*
Amount of corn (g/once)*
* The above-mentioned proportions are approximate and can be adapted according to the customer's choice
and needs.
BEFORE FIRST USE
Upon receipt of the goods, check the packaging for integrity and open it. If the packaging is damaged, ple-
ase contact your transport company and distributor within 3 days and document the damages in as much
detail as possible. Do not turn the package upside down! When transporting the package, please ensure
that it is kept horizontal and stable. Please keep all packaging materials (cardboard, plastic tapes and Styro-
foam) so that in case of a problem, the device can be sent back to the service centre as well-protected as
possible.
SAFETY INSTRUCTIONS
1. The popcorn machine should be placed where it has a strong and stable position (a 3% slant is an
advantage).
2. The device should only be connected with an appropriate power source.
3. The safety switch / power switch should be located near the machine. The path must be freely
accessible.
4. All electrical connections have to be carried out by authorized personnel only
FRONT PANEL
RCPS-16EB | RCPS-14
8
POPCORN MACHINE
RCPS-16EB | RCPS-14
230
1,495
50
220~250
50
50
150
1 2 3
Rev. 19.06.2018
1. TURN – turning on the stir function
2. HEAT – turning on the bowl heating
3. WARM & LIGHT – turning on the interior light and heating
OPERATION
1. In order to switch on the heating range and the light turn on the switch (Power & Light).
2. Turn on the switch (HEAT) and pre-heat the bowl for 5-6 minutes.Put 50 ml oil (coconut oil would be
best), 150 g corn and 50 g sugar into the pan.
3. Please note that during the production of popcorn, the door needs to be closed so that the hot
popcorn cannot escape and cause burns.
4. By turning on the stir function (TURN-switch) you can stir the popcorn until all corn is popped. Now,
tip the popcorn out of the bowl. To do that you have to operate the lever attached to the bowl.
5. You can repeat this procedure as often as you want to. It only takes approximately 2 minutes until
the corn pops steadily.
6. Do not let any oil drop on the hot plate as it can result in a fire. WARNING: Do not let any water
drip on the plate during the popcorn popping procedure.
7. The device is equipped with a thermostat. If the temperature exceeds the maximum the machine
switches off automatically to ensure the required safety.
Attention: The pot has to be emptied and the heating turned off as soon as the frequency (approx. 2-3
seconds) of popping slows down. Only like this, burning of sugar and popcorn as well as damage to the
coating can be prevented. It is not always possible for all corn to pop.
Remove residues after every production cycle.
We cannot assume liability for damages to the pot's coating due to improper use.

CLEANING AND MAINTENANCE

1. Switch off the device and disconnect the power plug in order to prevent accidents when cleaning
the machine.
2. To clean the device from the outside, use a wet cloth with some corrosion protection. DO NOT
clean the machine with water as it can damage the electric function of the device.
3. If the device is not used for a prolonged period of time, unplug the power plug.
4. DO NOT clean the inside of the device with hard metallic objects, as this will damage the coating
of the machine.
REGULAR CONTROL OF THE DEVICE
Control regularly that the device does not present any damage. If there is any damage, please stop using the
device. Please contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. Avoid formulations like "the device doesn´t heat",
which may mean that it does not heat enough or even not at all. These failures have different causes!
• The more detailed your information, the better the customer service will be able to solve your problem
rapidly and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to
a loss of warranty!
Rev. 19.06.2018 9