Product Dimensions; Cabinet Dimensions - KitchenAid KDRS505SS Instructions Pour L'installation

Product Dimensions

A
F
35³⁄₄ ¹⁄₈
A. " ± " (90.8 ± 0.3 cm)
cooktop height (minimum)
with leveling legs screwed all
the way in
B. Model/serial/rating plates
(located behind the control
panel)*
*Model/serial/rating plates may be rotated up from behind the
control panel for viewing from the front of the range.
**Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
***Excludes handle. Dimension given is from wall to front of oven
door and will vary based on electric outlet receptacle
installation.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
B*
C**
D
E***
47¹⁄₈ ¹⁄₈
C. " ± " (119.7 ± 0.3 cm)
overall height (minimum) with
leveling legs screwed all the
way in**
28¹⁄₂ ¹⁄₄
D. " ± " (72.4 ± 0.6 cm)
depth with handle
26¹⁄₈ ¹⁄₈
E. " ± " (66.4 ± 0.3 cm)
29¹⁵⁄₁₆ ¹⁄₁₆
F. " ± " (76.0 ± 0.2 cm)
width
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
A
F
K
8½"
(21.6 cm)
1½"
(3.8 cm)
1¼"*
(3.1 cm)
A. 18" (45.7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to the top of the cooktop, see NOTE.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of the range to the side
wall or other combustible material.
G. Cabinet door or hinges should not extend into the cutout.
H. 3" (7.6 cm) distance from wall
I. 1¹⁄₂" (3.8 cm) min. from right side cabinet
J. 8" (20.3 cm) width
K. 7" (17.8 cm) min. from floor
L. 2" (5.1 cm) min. from floor
*Drill on centerline 1¼" (3.1 cm) from rear wall for gas supply
line.
**Gas lines must be installed within the shaded area to ensure
proper alignment of this oven with cabinets.
***Recessed electrical plugs must be installed within the shaded
area to ensure proper alignment of this oven with cabinets.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is covered by not less than ¹⁄₄" (0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
D
B
C
E
J
G
I
L
H
L
14"
***
(35.6 cm)
2¼" (5.7 cm)
8½" (21.6 cm)**
gas line location
5