Cleaning And Maintenance - MSW -SR610 Manuel D'utilisation

Part number Description
21 Positioning plate
22 Bracket plate
23 Blade
24 Rear milling roll
25 Screw
26 Handle
27 Adjustment screw
28 Sleeve
29 Washer
30 Gear
31 Bottom milling roll
32 Top milling roll
33 Cover
34 Roll blocking
35 Shaft
36 Washer
37 Shield
38 Roll spaner
39 Hex screw
40 Hex screw
41 Hex screw
42 Hex screw
43 Hex screw
44 Hex screw
45 Hex screw
46 Washer
47 Hex screw
48 Hex screw
49 Washer
50 Nut
51 Hex screw
52 Hex screw
53 Hex screw
54 Hex screw
55 Washer
56 Hex screw
57 Hex screw
58 Hex screw
59 Hex screw
12
Part number Description
60 Adjustment screw
61 Washer
MSW-SR610
Part number Description
1 Base
2 Wedge
3 Lock washer M12
4 Washer M12
5 Hex screw 12-1.75x30
6 Hex screw 6-1.0x10
7 Needle bearing 7842/20
8 Cap screw 6-1.0x16
9 Hexagon nut
10 Bottom roll adjustment screw
11 Crank handle
12 Crankweb
13 Set screw
14 Lock washer 6
15 Rear roll adjustment screw
16 Right frame part
17 Roll pilot sleeve
18 Separator
19 Bottom milling roll
20 Rear milling roll
21 Top milling roll
22 Articulated sleeve
23 Separator
24 Lock washer 8
25 Hex screw 8-1.25x16
26 Hex screw 12-1.75x36
27 Key 4x4x19
28 Gear wheel 15T
29 Left frame part
30 Rack mandrel
31 Set screw
32 Gear wheel 19T
33 Adjustable block
34 Rack cover
Rev. 24.07.2018
MSW-SJ300
Part number Description
1 Base
2 Left frame part
3 Right frame part
4 Top milling roll
5 Top / bottom roll sleeve
6 Key 4x4x20
7 Bottom milling roll
8 Key 4x4x16
9 Rear milling roll
10 Rear roll sleeve
11 Handle screw M8-1.25x15
12 Handle
13 Holder
14 Gear wheel 15T
15 Washer 8mm
16 Cap screw M8-1.25x25
17 Work table
18 Rack cover
19 Gallery screw M8-1.25x35
20 Cap screw M6-1.0x12
21 Pitch
22 Gallery screw M8-1.25x40
23 Cap screw M5-0.8x10
24 Push spring
25 Screw M4-0.7x4
MSW-SR305
Part number Description
1 Screw M6x10
2 Grease dispenser
3 Sleeve
4 Adjustment knob
5 Left frame part
6 Sleeve
7 Key
8 Rear milling roll
9 Sleeve
10 Right frame part
11 Mandrel sleeve
Rev. 24.07.2018
Part number Description
12 Washer 6mm
13 Spring washer 6mm
14 Screw M6x16
15 Sleeve
16 Gear wheel
17 Top milling roll
18 Bottom milling roll
19 Holder
20 Nut M10
21 Handle
22 Screw M10x120
23 Adjustment knob
24 Adjustment knob
25 Base
26 Washer 10mm
27 Spring washer 10
28 Screw M10x20
29 Screw M6x6
30 Allen wrench
31 Washer 6

3.3. CLEANING AND MAINTENANCE

• Keep the levers and adjustment elements clean, free
of lubricant residues.
• Rotary elements and/or contact surfaces shall be kept
clean, free of rust traces and periodically protected
with thin films of specialistic oil.
• Use cleaners without corrosive substances to clean
each surface.
• After cleaning the device, all parts should be dried
before reusing it.
• Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
• In case of longer device disuse, protect it with grease
for the storage period. To ensure safe use, remove the
grease excess before reuse.
13