Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
g)
Children or unauthorised persons are forbidden from
entering a work station. (A distraction may result in a
loss of control over the device).
h)
During operation, take care of strangers and their
safety.
i)
Carefully observe the workpiece during operation, to
avoid its damage and prevent any possible hazard.
j)
Maintain order and remove any dust, debris and
waste material after working.
k)
If more elements are manufactured, they should be
stored both before and after operation in such a way
that enables you to maintain order at the workstation.
REMEMBER! When using the device, protect
children and other bystanders.
2.2. PERSONAL SAFETY
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
When working with the device, use common sense
and stay alert. Temporary loss of concentration whilst
using the device may lead to serious injuries.
c)
Use personal protection equipment as required
for working with the device, specified in section 1
(Legend). The use of correct, approved personal
protection equipment reduces the risk of suffering an
injury.
d)
Do not overestimate your abilities. When using the
device keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
e)
Do not wear loose clothing or jewellery. Keep hair,
clothes and gloves away from moving parts. Loose
clothing, jewellery or long hair may get caught in
moving parts.
f)
Before device operation, remove all regulating tools
or wrenches. Any tool or wrench left inside a rotating
part of the device can result in injuries.
g)
The material to be worked should be free of impurities.
h)
Do not touch any movable parts or accessories during
device operation.
i)
Use protective gloves to avoid being hurt by sharp
edges.
j)
Do not work on elements made of hard materials.
k)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
l)
Do not touch the gear during device operation.
2.3. SAFE DEVICE USE
a)
Do not overload the device. Use appropriate tools for
the given task. A correctly selected device will perform
the task for which it was designed better and in a safer
manner.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c)
Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
d)
Keep the device out of the reach of children.
10
e)
Device repair or maintenance should be carried out by
qualified persons, only using original spare parts. This
will ensure safe use.
f)
To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
g)
When transporting and handling the device between
the warehouse and the destination, take into account
the occupational health and safety principles for
manual transport operations which apply in the
country
h)
Use the device to work on elements of parameters
conforming with the data given in the technical data
table. Do not exceed the permissible dimensions of
the worked material.
i)
Do not work on two workpieces at the same time.
j)
Long workpieces must be supported and set stably for
working.
k)
Place the device on a stable, dry and flat surface,
the size of which should be adapted to the overall
dimensions of both the device and the materials to be
worked on.
l)
The floor at the workstation should be anti-slip.
m)
Dust can be produced during device operation.
Respiratory protection is recommended.
n)
Do not use the device to cut round beams, chains,
steel cables or elements made of hard materials.
3. USE GUIDELINES
Rolling mill (Model: MSW-SR610, MSW-SR305, MSW-SJ300) is
used to produce cylinder shapes from metal sheets and wires.
Mending machine (Model: MSW-MFM-3IN1-305) is used to
produce cylinder shapes, cut and bend metal sheets and wires.
The user is liable for any damage resulting from non-
intended use of the device.
3.1. DEVICE DESCRIPTION
MSW-SR610
4
3
2
8
1
MSW-SR305
9 4
2
3
1
8
Rev. 24.07.2018
MSW-SJ300
7
4
2
8
3
1
MSW-MFM-3IN1-305
2
4
2
1
3
5
6
7
1.
Crank
2.
Adjustment screw for the gap between rollers
3.
Adjustment screw for the cylinder diameter
4.
Milling rolls
5.
Top bending tool
6.
Bottom bending tool / cutting edge
7.
Work table
8.
Base
9.
Grease dispenser
3.2. PREPARING FOR USE/ DEVICE USE
Rolling (Model: MSW-SR610, MSW-MFM-3IN1-305, MSW-
SR305, MSW-SJ300):
•
Set the required gap between the milling rolls (4)
using the adjustment screw (2).
•
Insert the sheet between the rolls (4).
•
Set the required diameter of the output cylinder
using the adjustment screw (3).
•
Then, drive in the sheet between the milling
rolls using the crank (crank clockwise and then
counterclockwise).
•
Crank until the desired workpiece shape is obtained.
•
To remove the finished element, reduce the
adjustment screw (2) pressure and draw out the roll
with the finished element:
MSW-SR610/ MSW-SJ300
2
MSW-SR305
2
Rev. 24.07.2018
MSW-MFM-3IN1-305
2
•
A wire can also be milled in the device; the grooves
on either side of the milling rolls are used to this end.
Cutting (Model: MSW-MFM-3IN1-305):
•
Insert the workpiece between the cutting edge (6) and
the work table (7) and then crank counterclockwise
using the bending machine crank (1).
Bending (Model: MSW-MFM-3IN1-305):
•
Insert the workpiece between the top bending tool
(5) and the bottom bending tool (6) and then crank
counterclockwise using the bending machine crank (1).
ASSEMBLY DRAWINGS
PLEASE NOTE! This product's exploded view
can be found on the last pages of the operating
instructions (pp. 42-55).
List of elements:
MSW-MFM-3IN1-305
Part number
Description
1
Left frame part
2
Work table
3
Cross-beam
4
Crankweb
5
Right frame part
6
Frame
7
Plug
8
Platen bracket
9
Spring
10
Platen
11
Bottom bending tool
12
Top bending tool
13
Bending clamp
14
Screw
15
Sleeve
16
Guide
17
Adjustment screw
18
Holder
19
Screw
20
Positioning washer
11
Publicité
Table des Matières
