TROUBLEShOOTING
pOSSIBLE pROBLEM
EASY SOLUTION
Brewer will not switch on
•
Plug the Brewer into an independent outlet.
•
Check that the Brewer is plugged in securely.
•
Plug into a different outlet.
•
Reset circuit breaker if necessary.
•
Make sure that the Power Switch has been
turned on. The Water Tank should be illuminated.
The 'BREW' button,
be illuminated.
Brewer will not brew
•
After placing the K-Cup
My K-Cup
the Safety Locking Arm is pushed down securely The
LCD screen should indicate 'READY TO BREW'. The
and
button should illuminate & flash for up to 60 seconds.
•
If the LCD screen indicates 'REFILL TANK', add water
to the Water Tank or make sure the Water Tank is
attached correctly to the Brewer (page 18).
•
If the LCD screen indicates 'REFILL TANK' even
after refilling, contact Customer Service on
1-866-BREVILLE (1-866-273-8455).
•
If the 'BREW' button is not pressed in 60 seconds,
the LCD screen will indicate 'OPEN HEAD' and the
'BREW' button will be disabled to prevent accidental
activation. To re-activate the brew sequence, open the
Brewing Chamber Head by raising and lowering the
Safety Locking Arm completely.
•
The Exit Needle may be clogged (refer Cleaning the
K-Cup
®
Coffee is too weak
•
Reduce the brew size selection for a "stronger" tasting
or watery
cup of coffee (refer to Setting the 'BREW SIZE' feature,
page 24).
•
Try an Extra Bold K-Cup
ground coffee in each K-Cup
NOTE:
There are over 200 varieties of Keurig K-Cups
For more information on K-Cups
®
or K-Cup
Service on 1-866-BREVILLE, or visit www.breville.com.
32
All manuals and user guides at all-guides.com
and
buttons should
®
in the K-Cup
®
Holder, or the
®
Holder into the Brewing Chamber, ensure
buttons should illuminate and the 'BREW'
Holder, page 27).
®
. They have 30% more
®
portion pack.
®
from 13 gourmet partners.
®
ordering, call Breville Customer
TROUBLEShOOTING
pOSSIBLE pROBLEM
EASY SOLUTION
Brewer dispenses a
•
The Exit Needle may be clogged (refer to Cleaning the
partial cup
K-Cup® Holder, page 27).
•
The Water Tank may have been removed during
brewing. Replace the Water Tank and perform a
cleansing brew without a K-Cup® (refer to Brewing
Hot Water, page 18).
•
If the LCD screen indicates 'DESCALE', follow the
instructions, Descaling your Brewer (page 28)
•
If you have repeated the descale procedure on your
Brewer two times and the message is still displayed,
contact Customer Service on 1-866-BREVILLE
(1-866-273-8455).
The time is not displayed
•
The time will not be displayed on the LCD screen
on the LCD screen
unless you have set it. To set the clock, follow the
instructions, Setting the 'CLOCK SET' feature
(page 21).
•
If power is interrupted to the Brewer, you will need to
set the clock again.
Brewer shuts off or turns
•
Check to make sure that the 'ON-OFF TIME' and/
on automatically
or the 'AUTO OFF' features have not been set. To
do this, press the 'MENU' button and scroll through
the programming options. Both the 'ON-OFF TIME'
and 'AUTO OFF' features should be 'INACTIVE'. If
'INACTIVE' is not displayed, follow the instructions,
Setting the 'ON-OFF TIME' feature (page 21) and
Setting the 'AUTO OFF' feature (page 23).
The blue light in the
•
The water level is low and a full cup cannot be
water tank is flashing
brewed. Add water to the Water Tank, following the
instructions, Re-filling the Water Tank (page 18).
The LCD screen
•
Repeat the 'Descaling the Brewer' process (page 28).
continues to indicate
•
After the 'Descaling the Brewer' process, ensure to
'DESCALE' after
disconnect the power plug from the wall outlet for at
completing the process.
least 15 minutes, then re-plug the power plug into the
wall outlet.
33