Breville Gourmet Single Cup Brewer BKC600XL Livret D'instructions page 9

OpERATING YOUR BREVILLE GOURMET SINGLE CUp BREwER™
NOTE:
There are two sharp needles used
to puncture the K-Cup ® and My
K-Cup ® holder. One in the base of
the K-Cup ® holder, the other on the
underside of the Brewing Chamber
head. To avoid risk of injury, use
caution when inserting or removing
® ®
the K-Cup , K-Cup holder or My
K-Cup ® holder.
11. Lower the Safety Locking Arm to close
the Brewing Chamber Head over the
My K-Cup ® Holder. When closed
completely, the LCD screen will indicate
'READY TO BREW'. The and
buttons will illuminate and the 'BREW'
button will illuminate and flash for up to
60 seconds.
16
All manuals and user guides at all-guides.com
a) The LCD screen will indicate the
default brew size (7.25 oz.). To
choose a different size, press the
to go up in size or the button to
go down in size.
NOTE:
Select from a stronger small cup
(5.25 oz. serving), a small mug (7.25
oz. serving), a large mug (9.25 oz.
serving), a travel mug (11.25 oz.
serving) or iced beverage setting
(3.25oz serving). The iced beverage
setting is only available on the the
BKC700XL.
The small mug (7.25 oz. serving) is
the default brew size.
To program your favorite brew size,
refer to Setting the 'BREw SIZE'
feature (page 24).
NOTE:
To use the iced beverage setting,
place a tall glass filled with ice on
the drip tray. Use your favorite
K-Cup ® , select the iced beverage
brew size button. Add more ice once
brewing is complete, add cream and
sugar if desired. The iced beverage
setting is only available on the
BKC700XL.
b) Once the brew size is selected,
press the 'BREW' Button. The
'BREW' button will stop flashing,
the and buttons will no longer
be lit. The LCD screen will indicate
'BREWING' and the selected
brew size.
OpERATING YOUR BREVILLE GOURMET SINGLE CUp BREwER™
NOTE:
If the 'BREw' button is not pressed
in 60 seconds, the LCD screen
will indicate 'OpEN hEAD' and the
'BREw' button will be disabled to
prevent accidental activation. To
re-activate the brew sequence,
open the Brewing Chamber head
by raising and lowering the Safety
Locking Arm completely.
12. The LCD screen will indicate
'BREWING', however there may be a
short pause before the brewing process
begins. The process lasts about 60
seconds and ends with a burst of air to
remove all liquid from the My K-Cup ®
Holder.
NOTE:
There is extremely hot water in
the My K-Cup ® holder during the
brewing process. To avoid risk
of injury, do not raise the Safety
Locking Arm or open the Brewing
Chamber during the brewing
process.
Following the brew, the LCD screen
will indicate 'hEATING' as the
Brewer heats the water for the next
brew cycle. This process lasts about
15 seconds. The pump will make a
vibrating sound. This is normal.
13. Raise the Safety Locking Arm, remove
the assembled My K-Cup ® Holder. Use
®
caution as the My K-Cup Holder will
be hot.
14. Disassemble the My K-Cup ® Holder by
removing the Lid from the Holder in a
counter-clockwise direction. Remove
the Filter Basket from the Holder,
discard the grounds and rinse out the
Filter Basket and Holder.
15. 15. Enjoy your first cup of gourmet
coffee, tea or hot cocoa!
17