Elite Kura Mode D'emploi page 23

INSTRUCTIONS ON HOW TO
INSTALL THE FREEHUB WITH
CAMPAGNOLO
SPROCKET CASSETTES
• To replace the original freehub body installed
on Kura with the accessory body compatible with
Campagnolo 9/10/11 speed cassettes, follow
®
the procedure below:
1) Unscrew the right adapter on the sprocket
cassette with a 17mm key (Pic. 29).
2) Remove the spacer and the freehub body from
the Kura shaft (Pic. 30).
3) Fully insert the Campagnolo
compatible freehub body and replace the spacer
(Pic. 31 and Pic. 32).
4) Tighten the cog set shaft nut using a 17 mm
wrench to a torque of 5 Nm (44in-lbs). Use a
medium-strength oil tolerant threadlocker to lock
the nut on the shaft.
• Assemble the sprocket cassette on the freehub
by aligning the groove profiles.
• In order to use a Campagnolo
or others that employ the Campagnolo
you need to place the spacer (Rif. B) on the
freehub before inserting the sprocket cassette
(Pic. 7).
• If you're installing a 11-speed cassette by
Campagnolo or by other manufacturers that use
®
the Campagnolo Standard, place the sprocket
®
cassette onto the freehub body without using the
spacer. (Pic. 8) (Rif. B).
ATTENTION! Strictly follow the instructions
provided by the cassette manufacturer with
regard to specific installation techniques, the need
for additional spacers and torque specifications.
NOTE: Please contact your dealer if you have
questions about installation or if you cannot
install the cassette. The warranty does not cover
any DAMAGE to the bicycle and/or Kura in the
event of incorrect installation.
MAINTENANCE
Kura does not require any specific scheduled
maintenance, however the following precautions
are recommended:
• wipe the trainer clean with a cloth after each
training session to prevent the accumulation of
dust and sweat;
• do not clean or degrease the bicycle chain
while the bike is mounted on Kura as solvents
can cause irreparable damage to the bearings or
9/10/11 SPEED
®
cassette
®
9/10 cassette,
®
standard,
®
other internal mechanical parts;
• Check that the quick release is properly secured
and fully working before every training session.
WARNING:
The tension
transmission belt is tested on every product by
Elite's assembly department; do not alter belt
tension as the power sensor must be recalibrated
with every variation in belt tension.
• The belt tension may lessen after multiple uses
or after particularly intensive training sessions,
and as a consequence, the accuracy of the
transmission of the user power output may
reduced. If that's the case, you might need to
increase the transmission belt tension by the
following method:
1) Remove the motherboard cover (Pic. 34).
2) Loosen the adjustment locking screw by one
full turn, so that you can then turn the adjusting
nut (Pic. 35).
3) Turn the adjusting nut half a turn to tighten the
belt correctly (Pic. 36).
4) Screw the adjusting nut (of point 2) of a turn to
fix it (Pic. 35).
5) Begin the calibration procedure as indicated in
paragraph page 20.
6) Repeat the previous operation if data
transmission still not correct.
7) Once calibration
motherboard cover (Pic. 37).
WARNING!:
Make sure
procedure has been pre-approved by Elite's tech
assistance department before re-tensioning the
belt (Pic. 38). Breaking the anti-tampering seal
invalidates the product's warranty.
WARNING
• Kura becomes hot during use. Wait for it to cool
before touching the resistance unit covers.
• Use the Kura trainer as described in the manual.
• Kura is not equipped with an emergency brake.
• Kura has been designed and manufactured to
ensure maximum safety of the user and/or third
parties, but people, children and pets should be
kept away from the trainer during use as contact
with the moving parts of the trainer and the
bicycle may result in damage or injury.
• Never put your fingers or foreign objects of any
kind through the slots on Kura, as there will be
high risk of damage to the trainer and/or serious
physical injury.
• Before you start training, place the trainer in
a suitable location, away from any potentially
dangerous objects (furniture, tables, chairs...) so
of the internal
is done replace the
the re-tensioning
EN
23