Ce Marking Information - GRUPPO PIAZZETTA 80 Mode D'emploi

CE MARKING INFORMATION

GRUPPO PIAZZETTA S.p.A.
Via Montello, 22
31011 Casella d'Asolo (TV) - ITALY
Tel. +39.0423.5271 Fax.+39.0423.527240
Product definition:
Rigid Aluminium coated steel connecting flue pipes single wall for pellet stove use
Intended use or uses of the construction product:
Convey the products of combustion from heating appliances to the chimney
Designation 1 DN (80) - T400 - N1 - D - V2 - L05200 - G350 M
Designation 2 DN (100) - T400 - N1 - D - V2 - L05200 - G375 NM
Description of article:
PIPE AND RIGID BENDS DIAMETER 80 - 100 mm
PIPE T25 DIA.80 CM 25 PIPE T50 DIA.80 CM 50
PIPE T25 DIA.100 CM 25 PIPE T50 DIA.100 CM 50
BEND 90° DIA.80 16X16 BEND 90° DIA.80 16X16 W/INSP. BEND 90° DIA.100 18X18
BEND 45° DIA.100 12X12 RM WALL CONNECTOR DIA.80
T CONNECTOR DIA.80 W/ T CONNECTOR D.80 18X14 WITH
INSP. 18X14 P960 F SIDE INSPECTIONS
T CONNECTOR DIA.80 DX RM WALL CONNECTOR DIA.100
W/INSP MP973
Nominal size
Compressive strength
Flexural strength
Non-vertical installations
Thermal shock resistance
Coefficient of flow resistance
Freeze thaw resistance
Pressure classes
Condensation and steam resistance
class
Corrosion resistance class
Thermal resistance
NPD = Value not determined or not pertinent
Dates at a nominal speed of 6 m/s
according to EN 1859
PIPE T100 DIA.80 CM 100
BEND 45° DIA.80 12X12
BEND 90° DIA.80 16X16
T CONNECTOR DIA.80 W/INSP. 18X14
PELLET/01
T CONNECTOR DIA.80 RH W/INSP. MP970 06
Other parts
PIPE T100 DIA.80 CM 100
PIPE T100 DIA.100 CM 100
T CONNECTOR DIA.80 W/INSP.
18X14 PELLET/01
T CONNECTOR D.80 WITH
SUPPORT H=17-19
T CONNECTOR DIA.100 W/INSP.
20X16 PELLET/01
80 - 100 mm
Maximum load: 0.6 kN (15 m of straight elements with Dia.80 mm)
Tensile strength: NPD
NPD
Designation 1,2 DN (80-100): Yes
Designation 1 DN (80): G350 M
Designation 2 DN (100): G375 NM
For flue pipes dia. 80 mm:
With thermal insulation, 5 cm thick, on the flammable wall, in ventilated conditions and with thermal
conductivity λ at a temperature of 800°C no greater than 0.17 W/mK (λ at 200°C no greater than
0.08 W/mK), the distance may be reduced to 10 mm as indicated in the technical compliance report
no. 40007. Therefore, 5 cm of insulation + 1 cm distance = 6 cm total safety distance.
Mean roughness according EN 13384-1: 0.1216 mm
Friction factor: see table below
Yes
N1
D
V2
NPD
Friction factor
ζ
0.1017
0.1387
0.2773
0.6933
1.1555
obtained from data given in EN 13384-1
H07025750 / DT2000730 – 11
08
0476
H07900127-CPR-2016-01-04
EN 1856-2 : 2009
PIPE T25 DIA.80 CM 25 W/INSP.
PIPE T25 DIA.100 CM 25 W/INSP.
BEND 90° DIA.100 18X18 W/INSP.
T CONNECTOR DIA.80 DX W/INSP.
MP970 06
T CONNECTOR D.80-100 WITH
SUPPORT H=17-19
Without thermal insulation on flammable wall
and in ventilated conditions.
Friction
CB TRIM COLLAR DIA.80
CB TRIM COLLAR DIA.100
BEND 45° DIA.80 12X12
T CONNECTOR DIA.80 SX W/INSP.
MP970 06
T CONNECTOR DIA.80 SX W/
INSP. MP973
∆p [Pa]
2.2
3
6
15
25
29