Maintenance; Cleaning And Inspection; Ashes; Thermotte - Nordpeis Uno 1 Manuel D'installation

WARNING:
Never leave the air control in ignition mode for pro-
longed periods as this may lead to overheating.
IMPORTANT! Always remember to open the air
vent control (preferably also the door) before new
wood logs are inserted into a hot burn chamber.
Let the flames get a good grip on the wood before
the air control setting is reduced.
When the draught in the chimney is low and
the vent is closed, the gas from the firewood
can be ignited with a bang. This can cause
damage to the product as well as the immediate
environment.

6. Maintenance

Cleaning and inspection

The insert should be inspected thoroughly and cleaned
at least once per season (possibly in combination
with the sweeping of the chimney and chimney pipes).
Ensure that all joints are tight and that the gaskets are
rightly positioned. Exchange any gaskets that are worn
or deformed.
Remember that the insert must always be cold when
inspected.

Ashes

The ashes should be removed at regular intervals.
Be aware that the ashes can contain hot ember even
several days after the fire is finished. Use a container
of non-combustible material to remove the ashes. It is
recommended to leave a layer of ashes in the bottom
as this further insulates the burn chamber. Take care
with the Thermotte plates when the ashes are removed,
particularly when using an ash shovel, so as not to
damage them.

Thermotte™

The insulation plates (Thermotte - FIG 11) are classified
as "wear and tear" parts which will require to be
exchanged after some years. The wear time will depend
on the individual use of your product.
Nordpeis offers a one-year warranty on these parts.
After this, replacements can be purchased.
If new plates are needed, contact your dealer:
Uno 1, 2, 4, 5 - FIG 11:
A. Smoke baffle
B. Backplate
C. Bottom plate
+ Uno 5 - FIG 11A:
D. Side plate left
E. Side plate right
Please note: Wood logs that are too long can cause
strain and crack the plates, due to the tension created
between the side plates.
14

Door and glass

Should there be any soot on the glass it may be
necessary to clean it.
as other detergents may damage the glass. (NB! Be
careful, even dedicated glass cleaner can damage the
varnish on the door frame).
the glass is to use a damp cloth or kitchen roll paper
and apply some ash from the burn chamber. Rub
around the ash on the glass and finish off with a piece
of clean and damp kitchen roll paper. NB! Only clean
when the glass is cold.
Check regularly that the transition between the glass
and the door is completely tight.
Periodically, it may be necessary to change the gaskets
on the door to ensure that the burn chamber is air tight
and working optimally. These gaskets can be bought as
a set, usually including ceramic glue.
CERAMIC GLASS
CANNOT BE
RECYCLED
Ceramic glass should
be disposed of as resid-
ual waste, together with
pottery and porcelain
Recycling of the ceramic glass
Ceramic glass cannot be recycled. Old glass, breakage
or otherwise unusable ceramic glass must be discarded
as residual waste. Ceramic glass has a higher melting
temperature, and can therefore not be recycled together
with glass. If mixed with ordinary glass, it would damage
the raw material and could, in worst case end the
recycling of glass. It is an important contribution to the
environment to ensure that ceramic glass does not end
up with the recycling of ordinary glass.
Packaging recycle
The packaging accompanying the product should be
recycled according to national regulations.

7. Warranty

Use replacement parts recommended only by
the Manufacturer.
Any unauthorized modification of the appliance
without written permission of the Manufacturer
are prohibited.
For detailed description of the warranty conditions see
the enclosed warranty card or visit our website:
www.nordpeis.com
GB
Use dedicated glass cleaner,
A good advice for cleaning
Warning!
Warning!