R&G AB0006BK Instructions De Montage page 5

Right-hand side (as you sit on bike)

Remove the engine/frame mounting bolt labelled 'D' in picture 2 (please note this bolt has an in-
board nut which is reused on assembly (the nut is recessed into the frame tube and a deep socket
must be used)).

Remove the engine/frame mounting bolt labelled 'E' in picture 2.

Remove the radiator mounting bracket bolt labelled 'F' in picture 2.

Place the longest remaining bolt (item 12=100mm long) with washer (item 3) through the upper-
front mounting plate of the right-hand side adventure-bar (item 10) (this is the longer adventure-
bar) as labelled 'B' in picture 2.

Place the longest spacer (S0027=21mm long) over the exposed end of the bolt.

Offer into position as shown in picture B, use the original nut to hold in place (do not tighten at
this stage.

Place one of the M12 washers (item 3) onto the remaining shortest M12 bolts (item 5=70mm
long).

Place the 12mm spacer (item 7) into the frame recess in position labelled 'E' in picture 2.

Fit the bolt and washer through the upper/rear mounting plate of the adventure bar labelled 'E' in
picture 2 (place the remaining neoprene gasket (item 6) over the exposed end of bolt) and through
the spacer in the frame recess.

Place the M8 bolt and washer (item's 8 and 9) through the lower mounting plate of the adventure-
bars and the radiator mounting bracket and secure.

Tighten all the bolts evenly (the top two to no more than 40Nm and the lower to no more than
20Nm)
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 11/05/2012 (NSY)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com Email: info@rg-racing.com